ASRock IMB-A160-H manual Onboard Headers and Connectors, Pin LPT1 See p.10, No

Page 19

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Plac- ing jumper caps over the headers and connectors will cause permanent damage to the motherboard!

USB 2.0 Headers

(9-pin USB6_7)

(see p.10, No. 29)

(9-pin USB8_9)

(see p.10, No. 30)

(9-pin USB10_11)

(see p.10, No. 31)

(USB12)

(see p.10, No. 33)

USB_PWR

-B

+B

GND DUMMY

1

GND

+A

-A

USB_PWR

Besides six default USB 2.0 ports on the I/O panel, there are three USB 2.0 headers and one USB port on this motherboard. Each USB

2.0header can support two USB 2.0 ports.

Print Port Header

(25-pin LPT1)

(see p.10, No. 12)

SLCT

GND PE

GND BUSY

GND ACK#

GND SPD7

GND SPD6

GND SPD5

GND SPD4

GND SPD3

SLIN# SPD2

PINIT# SPD1

ERROR# SPD0

AFD# STB#

1

This is an interface for print port cable that allows conve- nient connection of printer devices.

Front Panel Audio Header

(9-pin HD_AUDIO1)

(see p.10, No. 35)

GND PRESENCE#

MIC_RET

OUT_RET

1

OUT2_L

J_SENSE

OUT2_R

MIC2_R MIC2_L

This is an interface for the front panel audio cable that allows convenient connec- tion and control of audio devices.

19

Image 19
Contents IMB-A160-H Disclaimer Copyright NoticeContents Uefi Setup Utility Introduction Package ContentsSpecifications Support CD ConnectorsBios Feature Rear Panel I/OPage ASRock Crashless Bios Unique FeaturesASRock Instant Flash IMB-A160 Motherboard LayoutLvds for IMB-A160 only LAN Port LED Indications I/O PanelPre-installation Precautions InstallationInstalling Memory Modules Dimm Expansion Slots PCI Express Slots Installing an Expansion CardInstalling Sata Hard Disks Power Connectors Pled System Power LED Installing the System PanelPwrbtn Power Switch Reset Reset SwitchPin LPT1 See p.10, No Onboard Headers and ConnectorsPIN CPU Fan Connector Inverter Power Control Header Optional Digital Input / Output Pin Header Jumpers Setup PWR-On Mode Jumper AT Mode Using Ahci Mode Operating System SetupSet Up Uefi Using Ahci Mode Set Up Uefi Use RAID Installation Guide to set the RAID configuration Utilities Menu Installing DriversRunning The Support CD Drivers MenuHot Plug and Hot Swap for Hard Disk Drives What is Hot Plug and Hot Swap?Hot Plug / Hot Swap Operation Guide Points for attention, before you process Hot Plug / Hot Swap Step How to Hot Plug / Hot Swap a HDDHow to Hot Unplug / Hot Swap a HDD Uefi Menu Bar IntroductionNavigation Keys Main Screen Advanced Screen SVM Mode CPU ConfigurationCool ‘n’ Quiet North Bridge Configuration Front Panel South Bridge ConfigurationRestore on AC/Power Loss Onboard HD AudioSata Controller Storage ConfigurationSata Mode Sata IDE Combined ModeSuper IO Configuration Acpi Configuration USB Mouse Power On USB Keyboard/Remote Power OnUSB 2.0 Controller USB ConfigurationLegacy USB Support TPM Support Trusted ComputingHardware Health Event Monitoring Screen CPU FAN1 SettingBoot From Onboard LAN Boot ScreenSetup Prompt Timeout Bootup Num-LockSecurity Screen Discard Changes and Exit Load Uefi DefaultsExit Screen Save Changes and Exit