Adjusting the Burners

TABLE NO. 1

Burner	Gas type	Pressur	Nozzle		Nominal flow rate
		e	diameter
		mbar	1/100 mm	g/h	l/h	kw	kcal/h
	Natural Gas G20	20	72	-	95	1	860
Auxiliary	Butane G30	30	50	73	-	1	860
	Propane G31	37	50	71	-	1	860
	Natural Gas G20	20	97	-	167	1,75	1505
Semirapid	Butane G30	30	65	127	-	1,75	1505
	Propane G31	37	65	125	-	1,75	1505
	Natural Gas G20	20	115	-	286	3	2580
Rapid	Butane G30	30	85	218	-	3	2580
	Propane G31	37	85	214	-	3	2580
	Natural Gas G20	20	120	-	276	2,9	2494
Fish burner	Butane G30	30	85	211	-	2,9	2494
	Propane G31	37	85	207	-	2,9	2494
Ultra	Natural Gas G20	20	135	-	334	3,5	3010
Rapid	Butane G30	30	95	254	-	3,5	3010
	Propane G31	37	95	250	-	3,5	3010

(model with gas oven and gas grill with double controls)

	Natural Gas G20	20	135	-	352	3,7	3182
Oven	Butane G30	30	90	269	-	3,7	3182
	Propane G31	37	90	264	-	3,7	3182
	Natural Gas G20	20	115	-	191	2	1720
Grill	Butane G30	30	68	145	-	2	1720
	Propane G31	37	68	143	-	2	1720

(model with gas oven and gas grill with single control, or gas oven and electric grill)

	Natural Gas G20	20	150	-	429	4,5	3870
Oven	Butane G30	30	90	327	-	4,5	3870
	Propane G31	37	90	321	-	4,5	3870
	Natural Gas G20	20	115	-	191	2	1720
Grill	Butane G30	30	68	145	-	2	1720
	Propane G31	37	68	143	-	2	1720

Adjusting the ”MINIMUM” of the burners:

Hob burner adjustment: follow the instructions below to adjust the minimum of the hob burners:

1.Light the burner setting the knob to the MINIMUM position (small flame).

2.Turn the knob of the tap, secured by simple pressure on the rod.

3.If the cooker does not have safety valves on the hob burners, insert a small slotted screwdriver in the hole of the tap rod (Figure 12) and turn the choke screw to the right or left, until the burner flame is at the minimum; if the cooker has safety valves, the choke screw is not situated on the rod hole, but on the body of the tap (Figure 13).

4.Make sure the flame does not go out, when switching quickly from the MAXIMUM to the MINIMUM position. Oven burner adjustment: follow the instructions below to adjust the minimum of the burners:

1.Unplug the appliance before making the adjustment

2.Remove the knobs

3.Remove the control panel by removing the screws from the below the panel

4.Insert the thermostat knob

5.Light the burner setting the knob to the MAXIMUM position (manual lighting with a match)

6.Close the oven door and operate the oven for at least 10 minutes.

7.Set the knob to the MINIMUM position (120°) and then remove it.

8.Use a slotted screwdriver on the choke screw (Figure

9.14) and, while observing the flame at the same time through the cooker porthole, evaluate the consistency of the flame so it remains on when switching quickly from the MINIMUM to the MAXIMUM position.

10.Reassemble the front panel, proceeding as above in point 3, in reverse Grill burner adjustment: follow the instructions below to adjust the minimum:

1)Light the burner setting the knob to the MAXIMUM position.

2)Close the oven door and operate the oven for at least 10 minutes.

3)Set the knob to the MINIMUM position (small flame) and then remove it.

4)The cooker is equipped with safety valves, use a small slotted screwdriver on the valve body (see fig. 13) and turn the choke screw to the right or left, while observing the flame at the same time through the cooker porthole, evaluate the consistency of the flame so it remains on when switching quickly from the MINIMUM to the MAXIMUM position.

WARNING: The above-mentioned adjustment should be made only with natural gas burners, while for those operating with liquid gas the screw must be locked at the end in a clockwise direction.