Instructions
About the controls on the air conditioner
Instructions Safety
Vent Control
The vent control is located behind the front grille on the right side of the air discharge area. When CLOSED, only the air inside the room will be circulated and conditioned. When OPEN, the vent allows outdoor fresh air exchange.
To open or close the vent:
1.Remove the front grille.
2.Remove the vent card screw.
3.Remove vent card, turn it over and replace it by locating rear hole in card over locating pin inside air discharge and reattaching screw at front.
The unit leaves the factory set at the CLOSE position.
Locating hole | Locating hole |
Screw hole | Screw hole |
OPEN position | CLOSE position |
(Mesh end toward back) | (Mesh end toward front) |
and Cleaning Operating
Air Direction
Horizontal louvers | Remove the front grille |
on the front grille | to adjust the vertical |
let you control the | louvers |
air direction up and | to direct the air left |
down. | or right. |
Auxiliary Controls – Dip Switches (location varies by model)
Installation Instructions Care
The auxiliary dip switch controls are located behind the room
The owner is responsible for checking switches and ensuring they are in the desired position.
Fan Cycle/Continuous - Cool
Fan Cycle/Continuous - Heat (on some models)
Class 2 (on some models)
No function (reserved for future use)
Consumer Support Troubleshooting Tips
Fan Cycle/Continuous - Cool
When this switch is enabled (UP), it allows the indoor |
|
|
|
|
| Fan Cycle/Continuous - Cool | ||||||
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
| |
fan to cycle on/off with the compressor. When this |
|
|
|
|
|
|
|
|
|
|
|
|
switch is disabled (DOWN), it allows the indoor fan to run |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
continuously. The default setting is down (continuous). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Fan Cycle/Continuous - Heat (on some models)
When this switch is enabled (UP), it allows the indoor |
|
|
|
|
|
|
| Fan Cycle/Continuous - Heat (on some models) | ||||
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| |
fan to cycle on/off with the heater operation. When this |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
switch is disabled (DOWN), it allows the indoor fan to run |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
continuously. The default setting is UP (cyclic). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Class 2 - Remote Thermostat (on some models)
| When this switch is enabled (UP), it allows the unit |
|
|
|
|
|
|
|
|
| Class 2 (on some models) | ||
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
| |
| to operate with a Class 2 Remote Control Wall |
|
|
|
|
|
|
|
|
|
|
|
|
| Thermostat. The unit controls are disabled. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
8 | The default setting is down (disabled). |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |