Pelco c3653m-a manual Wire the status, shunt, and exit inputs, Wire the readers

Page 14

Chapter 2: S-EIDC-U (ethernet Integrated Door Controller)

The steps necessary to wire an S-EIDC-U for a single door are as follows:

Step 1: Connect magnetic lock or door strike. Refer to the illustration above. The following information may be pertinent when dealing with locks or door strikes:

•A magnetic lock or door strike can be powered by the eIDC (12 VDC @ 450 mA or less). This is a shared load.

•The two Open Collector outputs “OC1” and “OC2” (Output 1 and Output 2) provide a maxi- mum of 12 VDC @ 450 mA combined.

•“OC1” and “OC2” each have their own “-” terminal but share a “+” terminal.

•“OC1” and “OC2” are software configurable “E” (energized) or “DE” (de-energized).

•Magnetic locks can be powered by the Open Collector output if it draws less than 450 mA. If it draws more than 450 mA, then it must be wired to the form C relay (5A @ 30 VDC) labeled “NC” and “NO” and powered externally.

•Relay (Output 3) has separate terminals for “C” (Common), “NO” (Normally Open), and “NC” (Normally Closed) but the software designation must match for proper status reporting.

Important: To meet UL requirements, listed panic hardware must be used to allow emergency exit from the protected area.

Step 2: Wire the status, shunt, and exit inputs.

Keep in mind the following points:

•Input devices can be wired to S-EIDC-U Inputs (IN) 1-4.

•“NO” or “NC” is software configurable with Inputs 1-4.

•“EOLR” (End Of Line Resistance) supervision is software selectable, and is supported with 1k ohm resistors.

Step 3: Wire the readers.

Keep in mind the following points:

•Reader IN (CRI) and Reader OUT (CRO) are internally configured each having their own Data 0 (CR-), Data 1 (CR+), DC+, and DC-.

•“DC1-” has a maximum load of 250 mA; “DC2-” has a maximum load of 250 mA.

•The sum of all 4 open collectors (OC1 + OC2 + DC1 + DC2) must not exceed 750 mA.

•There is a single terminal for optional Reader LED control and optional Buzzer control.

•Only Readers can be wired to the Reader’s Data 0 (CR-), and Data 1 (CR+) terminals.

14	Intelli-M Hardware Installation And Reference Guide

Image 14

Contents C3653M-A11/08 Hardware Installation And ReferencePelco, Inc. Worldwide Headquarters Preface TrademarksTable of Contents Recessed Mounting Box FCC Declaration Of Conformity S-EIDC-U, S-PCON-U UL Compliance S-EIDC-U, S-PCON-UOfficial Notices Official Notices Chapter 1 Intelli-M Hardware Overview Contents Intelli-MHardware Overview Using This ManualIntelli-MHardware Overview S-EIDC-UUsing This Manual Chapter 1 Intelli-MHardware OverviewChapter 1 Intelli-MHardware Overview ethernet Integrated Door Controller Contents Chapter 2 S-EIDC-UTechnical Features S-EIDC-UOverviewS-EIDC-U Wiring S-EIDC-UDoor ComponentsS-EIDC-UDoor Component Wiring Keep in mind the following points Step 2: Wire the status, shunt, and exit inputsStep 3 Wire the readers Keep in mind the following pointsPowering Up An S-EIDC-U Four Power OptionsDetermining The Network IP Address Type Setting A Static IP Address Within The S-EIDC-U Setting A DHCP IP Address Within The S-EIDC-U Setting An S-EIDC-UFor DHCP AddressingQuick Mount Assembly Breakdown Resetting An S-EIDC-UQuick Mount Assembly Page S-PCON-UOverview Chapter 3 S-PCON-U Power Connector ContentsWiring And Powering Up S-PCON-U Technical Features S-PCON-UOverviewWiring And Powering Up S-PCON-U S-PCON-UWiring and Powering up DiagramChapter 3 S-PCON-UPower Connector Sample S-EIDC-UGlobal Configuration Chapter 4 Wiring Connections And ConfigurationsContents S-EIDC-UWiring TerminalsS-EIDC-U Sample S-EIDC-UGlobal ConfigurationChapter 4 Wiring Connections And Configurations S-EIDC-UWiring Terminals Single Door Door Configuration With S-EIDC-U S-EIDC-UInstalling The eFamily Update Utility Appendix A eFamily Update UtilityContents eFamily Update ProcedureSupervisor Plus Users Installing The eFamily Update Utility2.Launch double click the “setup.exe” file Web Interface Users6.Click the “Close” button eFamily Update Procedure Before Updating Your eFamily DeviceFigure A-7 Connection Information Screen Figure A-6 Choice To Backup ScreenFigure A-5 Connection Information Screen Page Figure A-11 Connection Information Request Screen Figure A-12 Update In Process Screen Figure A-13 Update Complete ScreenErrors That Occur During Update Figure A-14 Example Error MessagePage Input Configuration Appendix B Demo Kit WiringDefaults Output ConfigurationAlarm Service Configuration Controller ConfigurationAccess Service Configuration Quick Mount Assembly Kit Enclosure S-EIDC-UTechnical SpecificationsDimensions Ethernet Integrated Door ControllerReader Ports PowerCommunication InputsDimensions S-PCON-UTechnical Specifications Power ControllerOperational Power Connector Module S-PCON-UPower Out Power InDC Power --24 VDC, 1A DC Power --22.9 to 24 VDC, 1AMinimum Server Requirements Miscellaneous Computer Hardware SpecificationsPerformance Communications Server Requirements Performance Badging / Workstation RequirementsUSB Camera WebCam Minimum Badging / Workstation RequirementsDigital Camera Signature Capture