Pelco c3653m-a Appendix B Demo Kit Wiring, Defaults, Input Configuration, Output Configuration

Page 39

Appendix B: Demo Kit Wiring

Appendix B: Demo Kit Wiring

The following data provides the default configuration parameters if wiring the S-EIDC-U for a demo kit.

Important: An alarm is defined within Intelli-M as an event (i.e., alert) that is sent to the software monitoring the S-EIDC-U. This is not a “burglar alarm” nor has it has not been verified by UL.

S-EIDC-U Demo Kit Wiring

Defaults:

•Inputs: Demo Kit Inputs (Push buttons or Toggles) should be wired as Normally Open

•Outputs: Initial Status = De-Energized

Input Configuration:

•Input 1: Door Contact (NO)

•Input 2: REX (NO)

•Input 3: REX Free Egress (NO)

Output Configuration:

•Output 1: Door Strike (DE)

•Output 2: Alarm LED (DE)

•Output 3 Door Status LED (DE)

•Output 4 Buzzer (DE)

Intelli-M Hardware Installation And Reference Guide

39

Image 39

Contents Hardware Installation And Reference Pelco, Inc. Worldwide HeadquartersC3653M-A11/08 Trademarks PrefaceTable of Contents Recessed Mounting Box UL Compliance S-EIDC-U, S-PCON-U Official NoticesFCC Declaration Of Conformity S-EIDC-U, S-PCON-U Official Notices Intelli-MHardware Overview Using This Manual Chapter 1 Intelli-M Hardware Overview ContentsS-EIDC-U Intelli-MHardware OverviewChapter 1 Intelli-MHardware Overview Using This ManualChapter 1 Intelli-MHardware Overview Chapter 2 S-EIDC-U ethernet Integrated Door Controller ContentsS-EIDC-UOverview Technical FeaturesWiring S-EIDC-UDoor Components S-EIDC-UDoor Component WiringS-EIDC-U Keep in mind the following points Step 2: Wire the status, shunt, and exit inputsStep 3 Wire the readers Keep in mind the following pointsFour Power Options Powering Up An S-EIDC-UDetermining The Network IP Address Type Setting A Static IP Address Within The S-EIDC-U Setting An S-EIDC-UFor DHCP Addressing Setting A DHCP IP Address Within The S-EIDC-UResetting An S-EIDC-U Quick Mount AssemblyQuick Mount Assembly Breakdown Page Chapter 3 S-PCON-U Power Connector Contents Wiring And Powering Up S-PCON-US-PCON-UOverview S-PCON-UOverview Technical FeaturesS-PCON-UWiring and Powering up Diagram Wiring And Powering Up S-PCON-UChapter 3 S-PCON-UPower Connector S-EIDC-UWiring Terminals Chapter 4 Wiring Connections And ConfigurationsContents Sample S-EIDC-UGlobal ConfigurationSample S-EIDC-UGlobal Configuration Chapter 4 Wiring Connections And ConfigurationsS-EIDC-U S-EIDC-UWiring Terminals S-EIDC-U Single Door Door Configuration With S-EIDC-UeFamily Update Procedure Appendix A eFamily Update UtilityContents Installing The eFamily Update UtilityWeb Interface Users Installing The eFamily Update Utility2.Launch double click the “setup.exe” file Supervisor Plus Users6.Click the “Close” button Before Updating Your eFamily Device eFamily Update ProcedureFigure A-6 Choice To Backup Screen Figure A-5 Connection Information ScreenFigure A-7 Connection Information Screen Page Figure A-11 Connection Information Request Screen Figure A-13 Update Complete Screen Figure A-12 Update In Process ScreenFigure A-14 Example Error Message Errors That Occur During UpdatePage Output Configuration Appendix B Demo Kit WiringDefaults Input ConfigurationController Configuration Access Service ConfigurationAlarm Service Configuration Ethernet Integrated Door Controller S-EIDC-UTechnical SpecificationsDimensions Quick Mount Assembly Kit EnclosureInputs PowerCommunication Reader PortsPower Connector Module S-PCON-U S-PCON-UTechnical Specifications Power ControllerOperational DimensionsDC Power --22.9 to 24 VDC, 1A Power InDC Power --24 VDC, 1A Power OutPerformance Badging / Workstation Requirements Miscellaneous Computer Hardware SpecificationsPerformance Communications Server Requirements Minimum Server RequirementsSignature Capture Minimum Badging / Workstation RequirementsDigital Camera USB Camera WebCam