Pelco c3653m-a manual Power, Communication, Reader Ports, Inputs, Outputs, Certifications

Page 42

Appendix C: Intelli-M® Hardware Technical Specifications

Power

Direct from PoE (Power over Ethernet) Switch

Note: PoE has not been UL verified.

Optional: External (24 VDC, 1 A) Power Supply

Note: Power Supply must be UL 294 listed with a power limited output rating of 9.5 to 24 VDC.

Communication

Ethernet -- 10 BaseT with a maximum distance of 100 meters (328 feet)

Cable -- CAT 5, CAT 5E, CAT 6

Reader Ports

There are 2 reader ports on an S-EIDC-U.

Reader Power -- 12 VDC @ 250 mA per reader port

Note: Shared with Output 1 and Output 2. Refer to “Outputs” below.

Reader Types -- Standard Wiegand

Note: Recommended standard Wiegand readers are the HID ProxPoint Plu 6005 series, HID ProxPro 5355 series, or XceedID model XF2100.

Note: Smart Card readers are not yet supported in the S-EIDC-U.

Inputs

There are 4 programmable inputs on an S-EIDC-U with configurable circuit type (contact closure or TTL) and optional EOLR (End Of Line Resistor) supervision. Plus there is an integrated infrared tamper.

Note: The tamper sensor can be programmed within the Alarm Services of the Supervisor Plus software, and must be enabled to meet UL requirements. Refer to the “Intelli-M Software Installation and Reference” manual. The Supervisor Plus software has not been UL verified.

Outputs

There are 3 programmable outputs and a built-in warning buzzer output on an S-EIDC-U.

Outputs 1 & 2 -- Open collector outputs with electronic overload protection (max 450 mA @ 12 VDC)

Note: The eIDC provides 750 mA of continuous power:

•The maximum total of all output power from the eIDC is 750 mA.

•The maximum output of either reader is 250 mA.

•The maximum output from the combined open collectors is whichever of the following is less: 450 mA or 750 mA less the sum of the readers.

Output 3 -- Form C, SPDT relay output with configurable initial state (max 5 Amp @ 30 VDC) Output 4 -- Built-in warning buzzer or alarm tone generator (max 85 dB)

Certifications

CE, FCC, ROHS, UL 294

42	Intelli-M Hardware Installation And Reference Guide

Image 42

Contents Hardware Installation And Reference Pelco, Inc. Worldwide HeadquartersC3653M-A11/08 Preface TrademarksTable of Contents Recessed Mounting Box UL Compliance S-EIDC-U, S-PCON-U Official NoticesFCC Declaration Of Conformity S-EIDC-U, S-PCON-U Official Notices Chapter 1 Intelli-M Hardware Overview Contents Intelli-MHardware Overview Using This ManualIntelli-MHardware Overview S-EIDC-UUsing This Manual Chapter 1 Intelli-MHardware OverviewChapter 1 Intelli-MHardware Overview ethernet Integrated Door Controller Contents Chapter 2 S-EIDC-UTechnical Features S-EIDC-UOverviewWiring S-EIDC-UDoor Components S-EIDC-UDoor Component WiringS-EIDC-U Keep in mind the following points Step 2: Wire the status, shunt, and exit inputsStep 3 Wire the readers Keep in mind the following pointsPowering Up An S-EIDC-U Four Power OptionsDetermining The Network IP Address Type Setting A Static IP Address Within The S-EIDC-U Setting A DHCP IP Address Within The S-EIDC-U Setting An S-EIDC-UFor DHCP AddressingResetting An S-EIDC-U Quick Mount AssemblyQuick Mount Assembly Breakdown Page Chapter 3 S-PCON-U Power Connector Contents Wiring And Powering Up S-PCON-US-PCON-UOverview Technical Features S-PCON-UOverviewWiring And Powering Up S-PCON-U S-PCON-UWiring and Powering up DiagramChapter 3 S-PCON-UPower Connector Sample S-EIDC-UGlobal Configuration Chapter 4 Wiring Connections And ConfigurationsContents S-EIDC-UWiring TerminalsSample S-EIDC-UGlobal Configuration Chapter 4 Wiring Connections And ConfigurationsS-EIDC-U S-EIDC-UWiring Terminals Single Door Door Configuration With S-EIDC-U S-EIDC-UInstalling The eFamily Update Utility Appendix A eFamily Update UtilityContents eFamily Update ProcedureSupervisor Plus Users Installing The eFamily Update Utility2.Launch double click the “setup.exe” file Web Interface Users6.Click the “Close” button eFamily Update Procedure Before Updating Your eFamily DeviceFigure A-6 Choice To Backup Screen Figure A-5 Connection Information ScreenFigure A-7 Connection Information Screen Page Figure A-11 Connection Information Request Screen Figure A-12 Update In Process Screen Figure A-13 Update Complete ScreenErrors That Occur During Update Figure A-14 Example Error MessagePage Input Configuration Appendix B Demo Kit WiringDefaults Output ConfigurationController Configuration Access Service ConfigurationAlarm Service Configuration Quick Mount Assembly Kit Enclosure S-EIDC-UTechnical SpecificationsDimensions Ethernet Integrated Door ControllerReader Ports PowerCommunication InputsDimensions S-PCON-UTechnical Specifications Power ControllerOperational Power Connector Module S-PCON-UPower Out Power InDC Power --24 VDC, 1A DC Power --22.9 to 24 VDC, 1AMinimum Server Requirements Miscellaneous Computer Hardware SpecificationsPerformance Communications Server Requirements Performance Badging / Workstation RequirementsUSB Camera WebCam Minimum Badging / Workstation RequirementsDigital Camera Signature Capture