Pelco c3653m-a manual Setting A Static IP Address Within The S-EIDC-U

Page 17
Setting A Static IP Address Within The S-EIDC-U

Chapter 2: S-EIDC-U (ethernet Integrated Door Controller)

This means a DHCP IP address cannot be determined (i.e., there is no DHCP connection). When this occurs, the S-EIDC-U will revert to its built in default static address of 169.254.1.1

Note: The default static address can be changed when the S-EIDC-U is configured. Refer to the section “Setting A Static IP Address Within The S-EIDC-U”below.

Setting A Static IP Address Within The S-EIDC-U

An S-EIDC-U can be statically addressed using a permanent IP Address, Subnet Mask, and Gateway (i.e., default route). To do this, perform the following steps:

1.To determine the current IP address of the controller, use the LEDs on the S-EIDC-U unit and note the IP address. If you look at the S-EIDC-U closely, each of the top five LEDs on each side have a number (left side 1-5 and right side 6-0).

2.Disconnect the power from the S-EIDC-U and then reconnect the power. The IP address of the device will be displayed three times on power up. IP address interpretation from LEDs is as follows:

•All LEDs will flash three times to begin the sequence. (The S-EIDC-U is fully operational dur- ing IP address flashing.)

•A numbered (LED) will flash representing each number in the IP address. Each number group is separated by all LEDs flashing once.

For example: 145.198.1.1 interprets as #1 flash #4 flash #5 flash <all flash> #1 flash #9 flash #8 flash <all flash> #1 flash <all flash> #1 flash <all flash>.

•Once the sequence has repeated 3 times, the S-EIDC-U LEDs will return to normal operation mode. Note that the entire sequence can be repeated at any time by power cycling the S-EIDC- U.

3.Obtain a valid static IP Address, Subnet Mask, and Gateway that is to be set into the S- EIDC-U from the Network Administrator of the facility where the S-EIDC-U is located.

4.Using a standard web browser, browse to the IP address obtained in Steps 1 and 2 above. Click the “Start” button to be presented with a login screen. The default user Name is admin and the default Password is admin (all lower case).

Note: If the Name and/or Password have been changed in the device and are unknown, the S-EIDC-U will need to be reset to its factory defaults to enable access. Refer to “Resetting an S-EIDC-U”later in this Chapter to perform a hardware reset.

5.Click the “System” button and then click “Controllers.”

6.Select the S-EIDC-U controller (i.e., click to highlight the line) and then click the “Modify” button.

7.Uncheck the “Use DHCP” box by clicking it. This enables the IP Address, Subnet Mask, and Gateway fields so that they can be changed.

8.Type the new IP Address, Subnet Mask, and Gateway information into the appropriate fields.

9.Click “Ok” and then “Done” to set the changes. The S-EIDC-U is now ready for further configuration and use.

Intelli-M Hardware Installation And Reference Guide

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents C3653M-A11/08 Hardware Installation And ReferencePelco, Inc. Worldwide Headquarters Trademarks PrefaceTable of Contents Recessed Mounting Box FCC Declaration Of Conformity S-EIDC-U, S-PCON-U UL Compliance S-EIDC-U, S-PCON-UOfficial Notices Official Notices Intelli-MHardware Overview Using This Manual Chapter 1 Intelli-M Hardware Overview ContentsS-EIDC-U Intelli-MHardware OverviewChapter 1 Intelli-MHardware Overview Using This ManualChapter 1 Intelli-MHardware Overview Chapter 2 S-EIDC-U ethernet Integrated Door Controller ContentsS-EIDC-UOverview Technical FeaturesS-EIDC-U Wiring S-EIDC-UDoor ComponentsS-EIDC-UDoor Component Wiring Step 3 Wire the readers Step 2: Wire the status, shunt, and exit inputsKeep in mind the following points Keep in mind the following pointsFour Power Options Powering Up An S-EIDC-UDetermining The Network IP Address Type Setting A Static IP Address Within The S-EIDC-U Setting An S-EIDC-UFor DHCP Addressing Setting A DHCP IP Address Within The S-EIDC-UQuick Mount Assembly Breakdown Resetting An S-EIDC-UQuick Mount Assembly Page S-PCON-UOverview Chapter 3 S-PCON-U Power Connector ContentsWiring And Powering Up S-PCON-U S-PCON-UOverview Technical FeaturesS-PCON-UWiring and Powering up Diagram Wiring And Powering Up S-PCON-UChapter 3 S-PCON-UPower Connector Contents Chapter 4 Wiring Connections And ConfigurationsSample S-EIDC-UGlobal Configuration S-EIDC-UWiring TerminalsS-EIDC-U Sample S-EIDC-UGlobal ConfigurationChapter 4 Wiring Connections And Configurations S-EIDC-UWiring Terminals S-EIDC-U Single Door Door Configuration With S-EIDC-UContents Appendix A eFamily Update UtilityInstalling The eFamily Update Utility eFamily Update Procedure2.Launch double click the “setup.exe” file Installing The eFamily Update UtilitySupervisor Plus Users Web Interface Users6.Click the “Close” button Before Updating Your eFamily Device eFamily Update ProcedureFigure A-7 Connection Information Screen Figure A-6 Choice To Backup ScreenFigure A-5 Connection Information Screen Page Figure A-11 Connection Information Request Screen Figure A-13 Update Complete Screen Figure A-12 Update In Process ScreenFigure A-14 Example Error Message Errors That Occur During UpdatePage Defaults Appendix B Demo Kit WiringInput Configuration Output ConfigurationAlarm Service Configuration Controller ConfigurationAccess Service Configuration Dimensions S-EIDC-UTechnical SpecificationsQuick Mount Assembly Kit Enclosure Ethernet Integrated Door ControllerCommunication PowerReader Ports InputsOperational S-PCON-UTechnical Specifications Power ControllerDimensions Power Connector Module S-PCON-UDC Power --24 VDC, 1A Power InPower Out DC Power --22.9 to 24 VDC, 1APerformance Communications Server Requirements Miscellaneous Computer Hardware SpecificationsMinimum Server Requirements Performance Badging / Workstation RequirementsDigital Camera Minimum Badging / Workstation RequirementsUSB Camera WebCam Signature Capture
Top Page Image Contents