Pelco c3653m-a manual Before Updating Your eFamily Device, eFamily Update Procedure

Page 32

Before Updating Your eFamily Device

Appendix A: eFamily Update Utility (Backup, Upgrade, And Restore eFamily Device Software)

Before Updating Your eFamily Device

To update an eFamily device, you must first gather the following information for the procedure:

•IP Address of the device you want to update

•Port number configured for communication (The default port number is 18777.)

•FTP Username and Password for that device

(The default Username and Password is the word “admin” without the quotes.)

•Location of the update file

If you are unsure of the IP address for the eFamily device you plan to update, power cycle the device. As the device boots, the IP address will be signalled by the LEDs. Refer to the “Determining The Network IP Address Type” section within Chapter 2 of this manual for details on reading the IP address from an eFamily device.

eFamily Update Procedure

Perform the following steps to update an eFamily device:

Important: If Supervisor Plus is running, shut it down before launching the eFamily Update Utility.

Note: The Supervisor Plus software has not been UL verified.

1.Launch the eFamily Update Utility (Start >> All Programs >.> Pelco >> Intelli-M Utilities >> eFamily Update Utility).

The following screen will be displayed.

Note: If your computer needs to be updated to .NET Framework 2.0, then installation screens for NET Framework will be displayed before the screen shown in Figure A-4 is displayed.

Figure A-4: eFamily Update Utility Screen

Click the “Next” button.

2.Type in the connection information used by the eFamily device to be updated.

A screen similar to that shown in Figure A-5 will be displayed requesting the path to the upgrade file. Type in the IP address. The TCP port number, FTP user name, and FTP password are system defaults. If you are unsure of the port number, user name, or pass-

32	Intelli-M Hardware Installation And Reference Guide

Image 32

Contents C3653M-A11/08 Hardware Installation And ReferencePelco, Inc. Worldwide Headquarters Preface TrademarksTable of Contents Recessed Mounting Box FCC Declaration Of Conformity S-EIDC-U, S-PCON-U UL Compliance S-EIDC-U, S-PCON-UOfficial Notices Official Notices Chapter 1 Intelli-M Hardware Overview Contents Intelli-MHardware Overview Using This ManualIntelli-MHardware Overview S-EIDC-UUsing This Manual Chapter 1 Intelli-MHardware OverviewChapter 1 Intelli-MHardware Overview ethernet Integrated Door Controller Contents Chapter 2 S-EIDC-UTechnical Features S-EIDC-UOverviewS-EIDC-U Wiring S-EIDC-UDoor ComponentsS-EIDC-UDoor Component Wiring Step 2: Wire the status, shunt, and exit inputs Step 3 Wire the readersKeep in mind the following points Keep in mind the following pointsPowering Up An S-EIDC-U Four Power OptionsDetermining The Network IP Address Type Setting A Static IP Address Within The S-EIDC-U Setting A DHCP IP Address Within The S-EIDC-U Setting An S-EIDC-UFor DHCP AddressingQuick Mount Assembly Breakdown Resetting An S-EIDC-UQuick Mount Assembly Page S-PCON-UOverview Chapter 3 S-PCON-U Power Connector ContentsWiring And Powering Up S-PCON-U Technical Features S-PCON-UOverviewWiring And Powering Up S-PCON-U S-PCON-UWiring and Powering up DiagramChapter 3 S-PCON-UPower Connector Chapter 4 Wiring Connections And Configurations ContentsSample S-EIDC-UGlobal Configuration S-EIDC-UWiring TerminalsS-EIDC-U Sample S-EIDC-UGlobal ConfigurationChapter 4 Wiring Connections And Configurations S-EIDC-UWiring Terminals Single Door Door Configuration With S-EIDC-U S-EIDC-UAppendix A eFamily Update Utility ContentsInstalling The eFamily Update Utility eFamily Update ProcedureInstalling The eFamily Update Utility 2.Launch double click the “setup.exe” fileSupervisor Plus Users Web Interface Users6.Click the “Close” button eFamily Update Procedure Before Updating Your eFamily DeviceFigure A-7 Connection Information Screen Figure A-6 Choice To Backup ScreenFigure A-5 Connection Information Screen Page Figure A-11 Connection Information Request Screen Figure A-12 Update In Process Screen Figure A-13 Update Complete ScreenErrors That Occur During Update Figure A-14 Example Error MessagePage Appendix B Demo Kit Wiring DefaultsInput Configuration Output ConfigurationAlarm Service Configuration Controller ConfigurationAccess Service Configuration S-EIDC-UTechnical Specifications DimensionsQuick Mount Assembly Kit Enclosure Ethernet Integrated Door ControllerPower CommunicationReader Ports InputsS-PCON-UTechnical Specifications Power Controller OperationalDimensions Power Connector Module S-PCON-UPower In DC Power --24 VDC, 1APower Out DC Power --22.9 to 24 VDC, 1AMiscellaneous Computer Hardware Specifications Performance Communications Server RequirementsMinimum Server Requirements Performance Badging / Workstation RequirementsMinimum Badging / Workstation Requirements Digital CameraUSB Camera WebCam Signature Capture