Pelco c3653m-a manual Controller Configuration, Access Service Configuration

Page 40

Controller Configuration:

Appendix B: Demo Kit Wiring

Controller Configuration:

•Description: S-EIDC-U 300

•IP Address: 169.254.1.1

•Serial #: Obtain from back of S-EIDC-U

•Reader Type:

•IN: Card reader

•OUT: Reader + keypad

Access Service Configuration:

•General Tab:

•Description: Basic Door

•Controller: S-EIDC-U (local default - 1.300)

•Lock Schedule: Default (1/0/0/0)

•Unlock Mode: Default Pulse (4 sec)

•Door Open Too Long: Default

•Anti-Passback: Default

•Inputs Tab:

•Input 1 – Door Contact (Enable Door Status)

•Outputs Tab:

•Lock Outputs:

•Output 1 – Door Strike

•Output 3 – Door Status LED

•Warning Outputs:

•Output 4 – Buzzer

•Triggers Tab:

•Triggers:

•CR-IN – Reader

•CR-OUT – Reader + keypad

•Input 2 - REX

Alarm Service Configuration:

•General Tab

•Controller: S-EIDC-U (local default - 1.300)

•Input: Input 1 – Door Contact

•Output: Output 2 – Alarm LED

•Conditions: Input 3 – REX Free Egress

40	Intelli-M Hardware Installation And Reference Guide

Image 40

Contents Pelco, Inc. Worldwide Headquarters Hardware Installation And ReferenceC3653M-A11/08 Preface TrademarksTable of Contents Recessed Mounting Box Official Notices UL Compliance S-EIDC-U, S-PCON-UFCC Declaration Of Conformity S-EIDC-U, S-PCON-U Official Notices Chapter 1 Intelli-M Hardware Overview Contents Intelli-MHardware Overview Using This ManualIntelli-MHardware Overview S-EIDC-UUsing This Manual Chapter 1 Intelli-MHardware OverviewChapter 1 Intelli-MHardware Overview ethernet Integrated Door Controller Contents Chapter 2 S-EIDC-UTechnical Features S-EIDC-UOverviewS-EIDC-UDoor Component Wiring Wiring S-EIDC-UDoor ComponentsS-EIDC-U Step 2: Wire the status, shunt, and exit inputs Step 3 Wire the readersKeep in mind the following points Keep in mind the following pointsPowering Up An S-EIDC-U Four Power OptionsDetermining The Network IP Address Type Setting A Static IP Address Within The S-EIDC-U Setting A DHCP IP Address Within The S-EIDC-U Setting An S-EIDC-UFor DHCP AddressingQuick Mount Assembly Resetting An S-EIDC-UQuick Mount Assembly Breakdown Page Wiring And Powering Up S-PCON-U Chapter 3 S-PCON-U Power Connector ContentsS-PCON-UOverview Technical Features S-PCON-UOverviewWiring And Powering Up S-PCON-U S-PCON-UWiring and Powering up DiagramChapter 3 S-PCON-UPower Connector Chapter 4 Wiring Connections And Configurations ContentsSample S-EIDC-UGlobal Configuration S-EIDC-UWiring TerminalsChapter 4 Wiring Connections And Configurations Sample S-EIDC-UGlobal ConfigurationS-EIDC-U S-EIDC-UWiring Terminals Single Door Door Configuration With S-EIDC-U S-EIDC-UAppendix A eFamily Update Utility ContentsInstalling The eFamily Update Utility eFamily Update ProcedureInstalling The eFamily Update Utility 2.Launch double click the “setup.exe” fileSupervisor Plus Users Web Interface Users6.Click the “Close” button eFamily Update Procedure Before Updating Your eFamily DeviceFigure A-5 Connection Information Screen Figure A-6 Choice To Backup ScreenFigure A-7 Connection Information Screen Page Figure A-11 Connection Information Request Screen Figure A-12 Update In Process Screen Figure A-13 Update Complete ScreenErrors That Occur During Update Figure A-14 Example Error MessagePage Appendix B Demo Kit Wiring DefaultsInput Configuration Output ConfigurationAccess Service Configuration Controller ConfigurationAlarm Service Configuration S-EIDC-UTechnical Specifications DimensionsQuick Mount Assembly Kit Enclosure Ethernet Integrated Door ControllerPower CommunicationReader Ports InputsS-PCON-UTechnical Specifications Power Controller OperationalDimensions Power Connector Module S-PCON-UPower In DC Power --24 VDC, 1APower Out DC Power --22.9 to 24 VDC, 1AMiscellaneous Computer Hardware Specifications Performance Communications Server RequirementsMinimum Server Requirements Performance Badging / Workstation RequirementsMinimum Badging / Workstation Requirements Digital CameraUSB Camera WebCam Signature Capture