Pelco c3653m-a manual Resetting An S-EIDC-U, Quick Mount Assembly Breakdown

Page 19

Resetting An S-EIDC-U

Chapter 2: S-EIDC-U (ethernet Integrated Door Controller)

Resetting An S-EIDC-U

To perform a hardware reset of an S-EIDC-U, perform the following steps:

Step 1: Disconnect power from the S-EIDC-U. Refer to the “Powering Up An S-EIDC-U”section above to see the possible power connections.

Step 2: Disconnect any wiring that may be connected at Input 2 and at BUZ. Then place a jumper at Input 2 and BUZ (that is, connect the Input 2 terminal to the BUZ terminal with a wire.)

Step 3: Reconnect power to the S-EIDC-U, and then after about 3 or 4 seconds remove the jumper (without removing power) that connects the Input 2 terminal to the BUZ terminal.

Step 4: Wait for the LEDs to start flashing the IP address sequence. (You may have to wait up to 5 minutes before the flashing occurs.) Once the LEDs start to flash, recycle power to the S-EIDC-U by disconnecting the power to the S-EIDC-U and then reconnecting the power.

Once Step 4 has been performed, the reset procedure is complete and the S-EIDC-U will have been restored to its factory default.

Quick Mount Assembly

The S-EIDC-U fits in any standard double-gang box, and simply clicks into the mounting plate.

Note: To meet UL requirements, unauthorized access of the Quick Mount Assembly is not permitted.

Quick Mount Assembly Breakdown

Intelli-M Hardware Installation And Reference Guide

19

Image 19

Contents Pelco, Inc. Worldwide Headquarters Hardware Installation And ReferenceC3653M-A11/08 Trademarks PrefaceTable of Contents Recessed Mounting Box Official Notices UL Compliance S-EIDC-U, S-PCON-UFCC Declaration Of Conformity S-EIDC-U, S-PCON-U Official Notices Intelli-MHardware Overview Using This Manual Chapter 1 Intelli-M Hardware Overview ContentsS-EIDC-U Intelli-MHardware OverviewChapter 1 Intelli-MHardware Overview Using This ManualChapter 1 Intelli-MHardware Overview Chapter 2 S-EIDC-U ethernet Integrated Door Controller ContentsS-EIDC-UOverview Technical FeaturesS-EIDC-UDoor Component Wiring Wiring S-EIDC-UDoor ComponentsS-EIDC-U Keep in mind the following points Step 2: Wire the status, shunt, and exit inputsStep 3 Wire the readers Keep in mind the following pointsFour Power Options Powering Up An S-EIDC-UDetermining The Network IP Address Type Setting A Static IP Address Within The S-EIDC-U Setting An S-EIDC-UFor DHCP Addressing Setting A DHCP IP Address Within The S-EIDC-UQuick Mount Assembly Resetting An S-EIDC-UQuick Mount Assembly Breakdown Page Wiring And Powering Up S-PCON-U Chapter 3 S-PCON-U Power Connector ContentsS-PCON-UOverview S-PCON-UOverview Technical FeaturesS-PCON-UWiring and Powering up Diagram Wiring And Powering Up S-PCON-UChapter 3 S-PCON-UPower Connector S-EIDC-UWiring Terminals Chapter 4 Wiring Connections And ConfigurationsContents Sample S-EIDC-UGlobal ConfigurationChapter 4 Wiring Connections And Configurations Sample S-EIDC-UGlobal ConfigurationS-EIDC-U S-EIDC-UWiring Terminals S-EIDC-U Single Door Door Configuration With S-EIDC-UeFamily Update Procedure Appendix A eFamily Update UtilityContents Installing The eFamily Update UtilityWeb Interface Users Installing The eFamily Update Utility2.Launch double click the “setup.exe” file Supervisor Plus Users6.Click the “Close” button Before Updating Your eFamily Device eFamily Update ProcedureFigure A-5 Connection Information Screen Figure A-6 Choice To Backup ScreenFigure A-7 Connection Information Screen Page Figure A-11 Connection Information Request Screen Figure A-13 Update Complete Screen Figure A-12 Update In Process ScreenFigure A-14 Example Error Message Errors That Occur During UpdatePage Output Configuration Appendix B Demo Kit WiringDefaults Input ConfigurationAccess Service Configuration Controller ConfigurationAlarm Service Configuration Ethernet Integrated Door Controller S-EIDC-UTechnical SpecificationsDimensions Quick Mount Assembly Kit EnclosureInputs PowerCommunication Reader PortsPower Connector Module S-PCON-U S-PCON-UTechnical Specifications Power ControllerOperational DimensionsDC Power --22.9 to 24 VDC, 1A Power InDC Power --24 VDC, 1A Power OutPerformance Badging / Workstation Requirements Miscellaneous Computer Hardware SpecificationsPerformance Communications Server Requirements Minimum Server RequirementsSignature Capture Minimum Badging / Workstation RequirementsDigital Camera USB Camera WebCam