Pelco c3653m-a manual Wiring And Powering Up S-PCON-U, S-PCON-UWiring and Powering up Diagram

Page 23

Wiring And Powering Up S-PCON-U

Chapter 3: S-PCON-U (Power Connector)

Wiring And Powering Up S-PCON-U

When the S-PCON-U is connected to a PoE enabled switch, electronics inside the S-PCON-U signal the PoE switch to place power onto the input ethernet cable. This power is then directed by the S-PCON-U onto the output RJ45 Ethernet connector. When the S-PCON-U is connected to a non-PoE enabled switch it is necessary to provide an external power supply to the S-PCON-U. This DC power is then directed onto the output RJ45 Ethernet connector. If both a PoE enabled switch and DC power are connected to the S-PCON-U, priority is given to the DC power supply.

Important: The S-PCON-U device and its Power Supply must be installed within the protected area (locked area) of the access facility to meet UL requirements.

@

22.9-24VDC@1A

@

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

S-PCON-U Wiring and Powering up Diagram

The output LED on the S-PCON-U provides visual feedback that the device is functioning. The LED can be illuminated green to indicate output voltage is greater than 24 VDC, amber to indicate that output voltage is between 22 and 24 VDC, or red to indicate that output voltage is below 22 VDC.

Warning: When the S-PCON-U is operating DO NOT CONNECT any ethernet device other than an S-EIDC-U to the output RJ45 connector. Damage to electronics inside the connected ethernet device could result.

Important: It is important to maintain correct polarity when connecting a DC supply to S-PCON-U. Check for proper connection of the DC supply on the provided plug prior to connecting the supply to the S-PCON-U.

Intelli-M Hardware Installation And Reference Guide

23

Image 23

Contents C3653M-A11/08 Hardware Installation And ReferencePelco, Inc. Worldwide Headquarters Trademarks PrefaceTable of Contents Recessed Mounting Box FCC Declaration Of Conformity S-EIDC-U, S-PCON-U UL Compliance S-EIDC-U, S-PCON-UOfficial Notices Official Notices Intelli-MHardware Overview Using This Manual Chapter 1 Intelli-M Hardware Overview ContentsS-EIDC-U Intelli-MHardware OverviewChapter 1 Intelli-MHardware Overview Using This ManualChapter 1 Intelli-MHardware Overview Chapter 2 S-EIDC-U ethernet Integrated Door Controller ContentsS-EIDC-UOverview Technical FeaturesS-EIDC-U Wiring S-EIDC-UDoor ComponentsS-EIDC-UDoor Component Wiring Keep in mind the following points Step 2: Wire the status, shunt, and exit inputsStep 3 Wire the readers Keep in mind the following pointsFour Power Options Powering Up An S-EIDC-UDetermining The Network IP Address Type Setting A Static IP Address Within The S-EIDC-U Setting An S-EIDC-UFor DHCP Addressing Setting A DHCP IP Address Within The S-EIDC-UQuick Mount Assembly Breakdown Resetting An S-EIDC-UQuick Mount Assembly Page S-PCON-UOverview Chapter 3 S-PCON-U Power Connector ContentsWiring And Powering Up S-PCON-U S-PCON-UOverview Technical FeaturesS-PCON-UWiring and Powering up Diagram Wiring And Powering Up S-PCON-UChapter 3 S-PCON-UPower Connector S-EIDC-UWiring Terminals Chapter 4 Wiring Connections And ConfigurationsContents Sample S-EIDC-UGlobal ConfigurationS-EIDC-U Sample S-EIDC-UGlobal ConfigurationChapter 4 Wiring Connections And Configurations S-EIDC-UWiring Terminals S-EIDC-U Single Door Door Configuration With S-EIDC-UeFamily Update Procedure Appendix A eFamily Update UtilityContents Installing The eFamily Update UtilityWeb Interface Users Installing The eFamily Update Utility2.Launch double click the “setup.exe” file Supervisor Plus Users6.Click the “Close” button Before Updating Your eFamily Device eFamily Update ProcedureFigure A-7 Connection Information Screen Figure A-6 Choice To Backup ScreenFigure A-5 Connection Information Screen Page Figure A-11 Connection Information Request Screen Figure A-13 Update Complete Screen Figure A-12 Update In Process ScreenFigure A-14 Example Error Message Errors That Occur During UpdatePage Output Configuration Appendix B Demo Kit WiringDefaults Input ConfigurationAlarm Service Configuration Controller ConfigurationAccess Service Configuration Ethernet Integrated Door Controller S-EIDC-UTechnical SpecificationsDimensions Quick Mount Assembly Kit EnclosureInputs PowerCommunication Reader PortsPower Connector Module S-PCON-U S-PCON-UTechnical Specifications Power ControllerOperational DimensionsDC Power --22.9 to 24 VDC, 1A Power InDC Power --24 VDC, 1A Power OutPerformance Badging / Workstation Requirements Miscellaneous Computer Hardware SpecificationsPerformance Communications Server Requirements Minimum Server RequirementsSignature Capture Minimum Badging / Workstation RequirementsDigital Camera USB Camera WebCam