Pelco c3653m-a manual UL Compliance S-EIDC-U, S-PCON-U, Official Notices

Page 5

Official Notices

FCC Declaration Of Conformity (S-EIDC-U, S-PCON-U)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help

UL Compliance (S-EIDC-U, S-PCON-U)

Pelco models S-EIDC-U and S-PCON-U have been evaluated in accordance with the requirements of UL294, Standards for Access Control System Units, and found to comply with the aforementioned standards set by Underwriters Laboratories (UL).

Intelli-M Hardware Installation And Reference Guide

5

Image 5

Contents C3653M-A11/08 Hardware Installation And ReferencePelco, Inc. Worldwide Headquarters Trademarks PrefaceTable of Contents Recessed Mounting Box FCC Declaration Of Conformity S-EIDC-U, S-PCON-U UL Compliance S-EIDC-U, S-PCON-UOfficial Notices Official Notices Intelli-MHardware Overview Using This Manual Chapter 1 Intelli-M Hardware Overview ContentsS-EIDC-U Intelli-MHardware OverviewChapter 1 Intelli-MHardware Overview Using This ManualChapter 1 Intelli-MHardware Overview Chapter 2 S-EIDC-U ethernet Integrated Door Controller ContentsS-EIDC-UOverview Technical FeaturesS-EIDC-U Wiring S-EIDC-UDoor ComponentsS-EIDC-UDoor Component Wiring Step 3 Wire the readers Step 2: Wire the status, shunt, and exit inputsKeep in mind the following points Keep in mind the following pointsFour Power Options Powering Up An S-EIDC-UDetermining The Network IP Address Type Setting A Static IP Address Within The S-EIDC-U Setting An S-EIDC-UFor DHCP Addressing Setting A DHCP IP Address Within The S-EIDC-UQuick Mount Assembly Breakdown Resetting An S-EIDC-UQuick Mount Assembly Page S-PCON-UOverview Chapter 3 S-PCON-U Power Connector ContentsWiring And Powering Up S-PCON-U S-PCON-UOverview Technical FeaturesS-PCON-UWiring and Powering up Diagram Wiring And Powering Up S-PCON-UChapter 3 S-PCON-UPower Connector Contents Chapter 4 Wiring Connections And ConfigurationsSample S-EIDC-UGlobal Configuration S-EIDC-UWiring TerminalsS-EIDC-U Sample S-EIDC-UGlobal ConfigurationChapter 4 Wiring Connections And Configurations S-EIDC-UWiring Terminals S-EIDC-U Single Door Door Configuration With S-EIDC-UContents Appendix A eFamily Update UtilityInstalling The eFamily Update Utility eFamily Update Procedure2.Launch double click the “setup.exe” file Installing The eFamily Update UtilitySupervisor Plus Users Web Interface Users6.Click the “Close” button Before Updating Your eFamily Device eFamily Update ProcedureFigure A-7 Connection Information Screen Figure A-6 Choice To Backup ScreenFigure A-5 Connection Information Screen Page Figure A-11 Connection Information Request Screen Figure A-13 Update Complete Screen Figure A-12 Update In Process ScreenFigure A-14 Example Error Message Errors That Occur During UpdatePage Defaults Appendix B Demo Kit WiringInput Configuration Output ConfigurationAlarm Service Configuration Controller ConfigurationAccess Service Configuration Dimensions S-EIDC-UTechnical SpecificationsQuick Mount Assembly Kit Enclosure Ethernet Integrated Door ControllerCommunication PowerReader Ports InputsOperational S-PCON-UTechnical Specifications Power ControllerDimensions Power Connector Module S-PCON-UDC Power --24 VDC, 1A Power InPower Out DC Power --22.9 to 24 VDC, 1APerformance Communications Server Requirements Miscellaneous Computer Hardware SpecificationsMinimum Server Requirements Performance Badging / Workstation RequirementsDigital Camera Minimum Badging / Workstation RequirementsUSB Camera WebCam Signature Capture