Slant/Fin V-180, V-33 operating instructions Reference Table No

VICTORY

For a masonry vitreous tile-lined chimney which is not exposed to the outdoors, use Table 1 in this Slant/Fin manual for venting requirements. DO NOT install this system into an unlined masonry chimney.

If a masonry chimney is exposed to the outdoors on one or more sides below the roof line (exposed chimney), it must be re-lined with a UL LISTED metallic liner system. See Table 2 in this Slant/Fin manual for venting require- ments of metallic re-lined chimneys.

If a Type “B” vent system is used, it must NOT be exposed to the outdoors below the roof line. See Table 2 in this Slant/Fin manual for venting requirements. Vent connectors serving appliances vented by natural draft shall

NOT be connected into any portion of mechanical draft sys- tems operating under positive pressure. Single or multiple appliance venting is shown in Figures 6a and 6b.

All Victory boilers require a condensate drain and drain trap. Vent connectors must be liquid tight.

4

NATURAL DRAFT CHIMNEY AND TYPE “B” VENTING VICTORY boilers are power (fan assisted) vented boilers. All Victory boiler models can be PRESSURE side wall or verti- cally vented by connecting the proper 3" diameter vent to the 3" diameter collar and adapter factory equipped on the Victory boilers. See “HORIZONTAL PRESSURE VENTING” and “VERTICAL PRESSURE VENTING”.

Models V-33 and V-60 can ONLY be pressure vented as described above and must NOT be vented into a chimney or “B” vent.

Models V-90, V-120, V-150 and V-180 may be vented into a natural draft chimney or natural draft “B” vent if the factory equipped 3" diameter flue collar and adapter on the boiler is REMOVED and REPLACED by the 5" diameter flue collar

manufactured by Slant/Fin Corporation and included in the V- If90thethroughboilerV-vent180 shippingis to be installedcra es. (Seeintofiguresa natural6a anddraft6b.) masonry chimney or Type “B” venting, it must be in accordance with National Fuel Gas Code ANSI Z223.1- latest edition, Part 7, Part 11 and Appendix G.

Table 1. Masonry Vitreous Tile-Lined Chimney (not metal lined)

Chimneys not exposed to the outdoors below the roof line. (5" dia. collar must be used)				Reference Table No. *
Appliance	Connector	Requirements*		(ANSI Z223.1)
Victory Boilers	Type “B”	1.	Connector diameter must be upsized to 7".	11-3
(V-90, V-120, V-150 and V-180)		2.	Chimney height limits: Min. 15 ft., Max. 30 ft.
Single Appliance		3.	Lateral length restriction applies (see table 11-3)
		4.	Internal area of chimney: Min. 50 sq. in.,
			Max. 269 sq. in.
Victory Boiler	Single-wall	1.	Connector diameter must be upsized to 7".	11-4
(V-180 only)		2.	Chimney height limits: Min. 15 ft., Max. 30 ft.
Single Appliance		3.	Max. lateral length may not exceed 2 ft.
		4.	Internal area of chimney: Min. 50 sq. in.,
			Max. 269 sq. in.
Victory Boilers	Type “B”	1.	See table 11-8 for chimney height and connector	11-8
(V-90, V-120, V-150 and V-180)			length restrictions.
plus another gas appliance		2.	Connector may have to be upsized to 6" diameter
			to meet requirement of 11-8.
Victory Boilers	Single-wall	1.	See table 11-9 for chimney height and connector	11-9
(V-150 and V-180 only)			length restrictions.
plus another gas appliance		2.	Connector may have to be upsized to 6" diameter
			to meet requirement of 11-9.
Table 2. Type “B” Venting and Metal-Lined Masonry Chimney				Reference Table No. *
UL LISTED MATERIALS ONLY. (5” dia. collar must be used)
Appliance	Connector	Requirements*		(ANSI Z223.1)
Victory Boilers	Type “B”	See table 11-1 for minimum and maximum of vent		11-1
(V-90, V-120, V-150 and V-180)		height and lateral length restriction.
Single appliance
Victory Boiler	Single-wall	See table 11-2 for minimum and maximum of vent		11-2
(V-90, V-120, V-150 and V-180)		height and lateral length restriction.
Single appliance
Victory Boilers	Type “B”	1. See table 11-6 for vent height and connector		11-6
(V-90, V-120, V-150 and V-180)			length restrictions.
plus another gas appliance		2. Connector and vent diameter may have to be in-
			creased to 6” or 7” to meet requirement of table 11-6.
Victory Boilers	Single-wall	1. See table 11-7 for vent height and connector		11-7
(V-120, V-150 and V-180 only)			length restrictions.
plus another gas appliance		2. Connector and vent diameter may have to be
			increased to 6” to meet requirement of table 11-7.

* Also see Z223.1 Part 7 and see Part 11 for use of mentioned tables.