Vulcan-Hart BVD36FP52(F,L)N-1, BVP42FP52(F,L)N-1, BVD34FP50(F,L)N-1 Important Safety Information

Page 3
IMPORTANT SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

Before enclosing the vent pipe assembly, operate the appliance to ensure it is venting properly.

If this appliance is installed directly on carpeting,

Clothing or other flammable material should not be

 

tile or other combustible material other than wood

 

placed on or near the appliance.

 

flooring the appliance shall be installed on a metal or

Adequate accessibility clearances for servicing and

 

wood panel extending the full width and depth of the

 

 

proper operation.

 

appliance.

 

 

This appliance must not share or be connected to a

 

The base referred to above does not mean the fireproof

 

 

flue serving a separate solid-fuel burning appliance.

 

base as used on wood stoves. The protection is for rugs

 

 

Keep the area around your appliance clear of

 

that are extremely thick and light colored tile.

Children and adults should be alerted to the hazards

 

combustible materials, gasoline and other flammable

 

vapor and liquids.

 

of high surface temperatures and should stay away

 

 

Under no circumstances should any solid fuels

 

to avoid burns or clothing ignition.

Young children should be carefully supervised when

 

(wood, coal, paper or cardboard etc.) be used in this

 

appliance.

 

they are in the same room as the appliance.

 

 

 

 

• The flow of combustion and ventilation air must not be obstructed in any way.

Due to high temperatures the appliance should be located out of traffic and away from furniture and draperies.

Any part removed for servicing the appliance must be replaced prior to operating the appliance. Work should be done by a qualified service person.

Keep burner and control compartment clean.

Vent cap is hot while fireplace is in operation.

Installation and repair should be done by a QUALIFIED SERVICE PERSON. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding materials, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean.

DO NOT put anything around the fireplace that will obstruct the flow of ventilation air.

Clearance in accordance with local installation codes and the requirements of the gas supplier.

DO keep the appliance area clear and free from combustiblematerial,gasolineandotherflammable vapors and liquids.

DO examine venting system periodically and replace damaged parts.

DO make a periodic visual check of pilot and burners. Clean and replace damaged parts.

DO NOT use this fireplace if any part has been under water. Immediately call a qualified service technician to inspect the heater and to replace any part of the control system and any gas control which has been under water.

Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance.

19400-3-0406

Page 3

Image 3
Contents B-VENT GAS FIREPLACE The Keystone B Vent Zero Clearance Gas FireplaceEFFECTIVE DATE APRIL Section TABLE OF CONTENTSIMPORTANT SAFETY INFORMATION NO ODOR DETECTED - ODOR FADE SAFETY INFORMATION FOR USERS OF LP GASThat’s your signal to go into immediate action LP-GASWARNING ODORAppliance Certification INTRODUCTIONInstructions to Installer Qualified Installing AgencyBVD36 SPECIFICATIONSFIREPLACE DIMENSIONS Dim BVD34Figure Combustible Material CLEARANCESLOCATING FIREPLACE Mantel Chart FigureInstalling a New Main Gas Cock GAS SUPPLYChecking Manifold Pressures GAS SUPPLY CONTFigure Vent Pipe Clearance INSTALLATIONInstall the Fresh Air Kit - BVA1 Framing and FinishingINSTALLATION CONT Combustible Surround InstallationFinishing Figure Vent Runs VENTINGGeneral Maintenance Installing the Vent System in a ChaseVent Configuration VENTING CONTVent Size Never downsize venting diameters ClearancesEMBER MATERIAL PLACEMENT ON BURNER LOG PLACEMENT 5 LOG SETTOP BRANCH REAR LOG BOTTOM LOG LOG PLACEMENT 3 LOG SETEMBER PLACEMENT BOTTOM LOG LOCATOR PINSInitial Lighting OPERATING INSTRUCTIONSGAS CONTROL KNOB SHOWN IN OFF POSITION 750 Millivolt SystemElectric 120 volt Operated Remote Control, FREC OPERATING INSTRUCTIONS CONTWall Switch, FWS-1optional FRBC Battery Operated Remote ControlSTANDING PILOT WIRING DIAGRAM TO TURN OFF GAS TO FIREPLACE FOR YOUR SAFETY, READ BEFORE LIGHTINGSTANDING PILOT LIGHTING INSTRUCTIONS LIGHTING INSTRUCTIONSSTANDING PILOT TROUBLESHOOTING 4.Frequent pilot outage problem6.Glass Sooting B-VENTFIREPLACES STANDING PILOT PROPANE/LP GAS CONVERSIONCHECK SAFETY SHUTDOWN PERFORMANCE SAFETY SHUTDOWN SYSTEMPILOT ORIFICE CONVERSION OPTIONAL REMOTE CONTROL 120V DIRECT IGNITION DIRECT IGNITION WIRING DIAGRAMTO TURN OFF GAS TO APPLIANCE FOR YOUR SAFETY READ BEFORE LIGHTINGDIRECT IGNITION LIGHTING INSTRUCTIONS LIGHTING INSTRUCTIONSDIRECT IGNITION PROPANE/LP GAS CONVERSION DIRECT IGNITION TROUBLESHOOTINGDIRECT IGNITION PROPANE/LP GAS CONVERSION Maxitrol Valve ConversionVALVE CONVERSION Glass Cleaning Optional Kits MAINTENANCE AND SERVICEClean Burner and Control Compartment Cleaning ProcedureBVD34 & BVD36 PARTS LIST BVD34 & BVD36 PARTS VIEW 19400-3-0406Page BVP42 PARTS LIST BVP42 PARTS VIEW 19400-3-0406Page FBB4 OPTIONAL VARIABLE SPEED BLOWER INSTALLATION 110 VOLT AC FBB4 OPTIONAL VARIABLE SPEED BLOWER INSTALLATIONJUNCTION BOX FAN BLACK FAN SWITCH WHITE GROUND BLOWER ASSEMBLYJUNCTION BOX WIRING INSTALLATION INSTRUCTIONS STANDARD MILLIVOLT VALVE MODELS120V DIRECT IGNITION VALVE MODELS OPTIONAL ACCESSORIES Decorative Louver Mission DECORATIVE ACCESSORIESPage 19400-0-1005SERVICE NOTES HOW TO ORDER REPAIR PARTS SERVICE NOTES Page19400-3-0406 SERVICE NOTES 19400-3-0406Page Empire Comfort Systems, Inc Page19400-3-0406