Samsung SHR-6040P, SHR-6042P manual NTP Setup,  NTP Enable

Page 42

If you have set a public DDNS (dyndns.com, no- ip.com or changeip.com), it may take 30 to 60 seconds until the IP address of the host name (URL) can be updated in the DNS.

When using the network by connecting an IP router to the main system, the network port has to be designated from the setup menu of the IP router. The main system uses 1494ports (554-2048) for the TCP communication. When using it by assigning IP addresses dynamically to the main system while using the DHCP function supported by the IP router, the port number for the IP address dynamically assigned from the setup menu of the IP router needs to be designated. When using an IP router, it is recommended to designate the IP address and port number to be assigned to the main system from the setup menu of the IP router, to set a fixed IP address for the connection mode of the main system, and to enter the IP address designated to the IP router. Please refer to the IP router manual or contact the manufacturer for the IP router setup method.

NTP Setup

NTP Setup

Primary Address

pool.ntp.org

 

 

Secondary Address

asia.pool.ntp.org

 

 

Connection Status

NTP Enable

Test

 

 

 

 

 

 

 

 

 

trying.. 0%

 

 

 

 

 

 

 

OK

Cancel

 

 

 

 

 

 

 

 

Move/Control

Select

Exit

NTP Setup is used to configure the system for network- based synchronization.

Primary Address & Secondary Address Sets the NTP server address.

Connection Status

You can check the connection status with the NTP server by pressing “Test” after entering the NTP server address.

If the message “Success” is displayed, the NTP server is in the state possible to communicate; if the message “Failed” is displayed, it is not possible to communicate.

NTP Enable

When using the NTP function, please check the “NTP Enable” box.

When the DVR system time prior to operating the NTP setup function is set faster than the NTP standard time (in other words, the DVR system time is set to a past time through the NTP setup), the recording function will not operate for the protection of previously recorded data. The recording function will operate normally from the point that the newly set time exceeds the original time value.

When the NTP function is in use, a time change can not be made from the time setup menu and it only allows setting the standard time zone.

The synchronization between NTP server and DVR system will be performed every hour.

38_ menu setup

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Real Time DVR Key features of your DVR WHAT’S Included with Your DVRSafety regulations Before start BatteryOperating Temperature System ShutdownContents Search and play Appendix Introducing your real time DVR Controls on the DVRName Function Set up the audio On/Off function This LED indicates the status of backup operationWhen an alarm occurs, it cancels the alarm HDD, this LED repeatedly blinksSelection Time set from the system setupDisplay the 4-split screens Display the 9-split screensReal panel jacks Remote control Using the Numeric ButtonsZoom PresetStop MenuInstallation Checking installation environmentConnecting video, audio, and monitor To the Video in terminal with the system’s power turned offConnecting to Internet through Adsl Connecting the networkConnecting to Internet through Ethernet 10/100BaseT InternetConnecting the alarm input Connecting the alarm output Connecting the RS-485 device Connecting the USBOperating the system Live screen modeLive Live screen iconsLive screen modes Setting the audio on/off Freezing and zoomingEvent monitoring Spot-out monitoringZoom function Before use Menu setupUser login SystemTime/Date/Language Setup PasswordUser Add/Del Group AuthorityProfile System Log REC SDB Backup Success/Failure Login/Logout with the Search ModeAVI Backup Success/Failure SFX Backup Success/FailureSystem Information & Setup HDD Setup HDD Format  HDD END AlarmCamera  HDD ENDCamera Configuration Screen SetupPTZ Device Monitoring Remote Control DeviceLive Mode  Event Monitoring Duration Normal Duration Spot Mode Event Duration  CameraEvent record Record modeEvent Record Setup CIF Post Event Alarm Detection Setup Alarm Out  State10~300 Seconds Sets the duration for alarm output Motion Detection SetupVideo Loss Detection Setup  SensitivityBackup Record scheduleIP Setup NetworkModel Size Web Viewer Port Settings Ddns Setup Network StatusNTP Setup  NTP EnableNTP Setup ISO  Authentication Method Transfer Picture Setup Smtp Server Authentication Method  Stmp ServerBasic operation of pan, tilt & zoom PTZ camera control modePTZ camera control  PANPTZ device menu setup Preset setupYou can set the name of each Preset Preset Name SettingsCamera menu setup CameraRecording Recnormal recordingEvent recording Search date & time selection Search and playSearch screen Date Color DescriptionSearch channel selection & recording graph Playback Audio On/Off  Play Screen Mode Split Screen Viewing One Scene at a Time Single ScreenNet I Setup tool AppendixNet Reply message Comments Viewing the device-related settings Net I Live ViewerTo modify the registered device Camera Controls area Using layoutsCamera Tree area Viewing areaNet I Search Viewer Device Firmware UpdateTo update device firmware Query Generator areaBefore use Add/Remove User User Administration Edit PasswordReset Edit User Group AuthorityPTZ Device Settings Camera SettingsVideo Settings Enable/DisableMonitoring Mode Recording ModeEvent Recording Mode Motion Detection Zone Motion Detection SettingsVideo Loss Detection Settings SensitivityWeb Viewer Port Setting Network SettingsIP Configuration NTP ConfigurationUsed to configure the picture quality of individual cameras Image Transmission SettingsUsed to adjust the frame rate of individual cameras SDB ViewerMain Window of SDB Viewer SkipSpeed Zoom BackupVoice Playback Setting Digital ZoomSFX player SFX Player ExecutionIntroducing Web Viewer CPU Connecting WEB ViewerSystem Requirements MemoryAppendix Using Live Viewer OSD Information DisplaySPLIT-SCREEN Full Screen ModeYou can change the split mode by clicking each number icon Connected DVRChanging the Live Screen Mode Quad MODE, the screen refreshes at the preset intervalSaving the Live Screen on the PC Using PTZ Camera Changing the Live Screen ChannelYou can save the preset up to Using Search Viewer SPLIT-SCREENOnly Single and Quad Mode are available in Search menu Searching the Recorded Video in the Calendar Searching the Recorded Video in the Timeline Normal ModeExtension Mode Controlling PlaybackNames Features Pop-up menuPop-up Menu If user press Enter button, the pop-up menu will disappear This button controls PTZ directions at PTZ modeIt executes Freeze feature at Live screen VideoSpecifications SHR-6040 SHR-6042Outline drawings TroubleshootingsFAQ Connected sensors are not working Color or in abnormal shapeCause ProperlyOpen source license report on the product GNU General Public LicensePreamble Appendix No Warranty How to Apply These Terms to Your New Programs Repair or CorrectionWe protect your rights with a two-step method You must cause the whole of the work to Appendix Executable END of Terms and Conditions No WarrantyHow to Apply These Terms to Your New Libraries FoundationOpenSSL License Loss of USE, DATA, or Profits or Business InterruptionThis Software is Provided by Eric Young ‘‘AS IS’’ Correct disposal of batteries in this product
Related manuals
Manual 96 pages 13.66 Kb Manual 96 pages 31.91 Kb Manual 96 pages 49.16 Kb Manual 96 pages 55.63 Kb Manual 96 pages 1.09 Kb
Top Page Image Contents