Samsung SDM-090MP, SDM-090P manual Connecting to Alarm Sensor

Page 27

Digital Multiplexer SDM-090(P)

4.Connecting to ALARM SENSOR

1.Connect the ALARM terminal on the Unit’s Rear Panel to the SENSOR CORRESPONDING TO camera number.

2.Connect grounding wires.

3.Connect the HOT terminal on the Unit’s Rear Panel to the ALARM IN terminal on the VCR.

4.Connect the COLD terminal on the Unit’s Rear Panel to the COM terminal on the VCR.

5.Connect the A/R terminal on the Unit’s Rear Panel to the RESET terminal on the VCR.

CAUTIONS

Depending on the kinds of TIME LAPSE VCR, the name of REC TRIGGER OUT terminal may be different, so be sure to connect after checking its name.

TIME LAPSE VCR

	1	2	3	4	5
	6	7	8	9
	FROM SENSOR				External ALARM
	FROM SENSOR				Connect to device
					Connect to device

3-4

Image 27

Contents Digital Multiplexer Digital Multiplexer SDM 090P Do Not Expose This Equipment To Rain or Moisture Important Safeguards Digital Multiplexer SDM-090P Digital Multiplexer SDM-090P Contents Viii Occurrence and Handling of Alarm Chapter Introduction IntroductionPage Triplex Name of parts and FunctionMulti Screen REC CheckEnter RESET/ERASEList MenuRear Panel VCR IN/OUT BNC Installation Physical & Environmental Preparing for the InstallationPrecautions when Installing 15Cm Digital Multiplexer SDM-090P Unpacking Connecting to Other Devices Connecting to normal VCR and Monitor Connecting to Other DevicesConnecting to S-VHS VCR and S-VHS Monitor Connecting to Time Lapse VCR Connecting to Alarm Sensor Remote Control by connecting to PC 2TXDTRANSMITTEDDATA 3RXDRECEIVEDDATA 5SGSIGNALGROUNDPIN Number CH4 CH5 CH6 CH7 CH8 CH9 Multi Screen REC CHECK/PB Through LIVE/PB Triplex PIP ResetAscii CH1 CH2 CH3Chapter Initial operation Turn on power switchSetup a recording channel Change it to a desiring indication modeWhen desiring to see in the live screen/replay screen When desiring to see in the Triplex screenWhen desiring to see in the Full screen When desiring to see in the division screen When desiring to see automatic sequential conversion screen Freeze setting of Full screen When desiring to see the stop screenWhen desiring to see in the zoom screen When desiring to see in the PIP screenFull Mode When desiring to see output of VCR as it is When desiring to see in the record screenSetting of Program Menu Record setting of each camera REC OUT SET REC Type TLVDuty SET Reservation OFF REC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 REC Type NOR ↔ TLVSetting of display mode Sequence Loss Detect Loss Info Alarm Info ALLPB Display ALL Spot OUT Cvbs PIP Size Alarm S/W Time CH1 02 CH2 CH3 02 CH4 CH5 02 CH6 CH7 02 CH8 CH9 SequenceTitle SET Setting of title by channelYY/MM/DD MM/DD/YY DD/MM/YY 01/04/01 123001 YY/MM/DD Hhmmss DATE/TIME SET Display TypeREC Type NOR ↔ TL Setting of alarmAlarm SET Hold Time REC Type NOR Alarm Input OFFSystem SET Baud Rate System settingPassword Change Alarm Buzzer OFF Loss Buzzer Summer TimePassword Change Password Check NEW Password Confirm +++++++++++++++++ + - - - - + Recording Digital Multiplexer SDM-090P Frame Normal record modeWeight value REC Duty record Time Lapse record modeAlarm weight value record Reservation recordREC Duty Alarm, loss Digital Multiplexer SDM-090P Screen conversion Alarm occurrence conditionsAlarm release Alarm recordVCR Trig Alarm signal standardALARM/LOSS List YY/MM/DD Hhmmss Alarm/Loss list referenceOperation in video loss Appendix a Appendix a Specifications Auto Switcher Outside Drawing Appendix B Appendix B Checking points in trouble When S-VHS record is not performed

Related manuals

Manual 41 pages 18.63 Kb