Samsung SDM-090MP, SDM-090P manual Password Change Password Check NEW Password Confirm

Page 49

Digital Multiplexer SDM-090(P)

-The following screen is displayed if pressing the “ENTER” button when the blinking position is at the “PASSWORD CHANGE…”:

[PASSWORD CHANGE]

PASSWORD CHECK

- - - - - - - -

NEW PASSWORD

- - - - - - - -

CONFIRM

- - - - - - - -

¥The password in shipment from factory is “12345678”.

¥The first digit from the initial password check blinks.

Press the current password in order of “1” ~ “9” of the “camera select” button.

¥The first digit of the new password blinks if properly entering the password check as per the current password.

¥Enter 8 characters of the new password to set using the “1” ~ “9” of the “camera select” button.

¥Enter a new password once again from the CONFIRM.

¥Message of “ERROR TRY AGAIN” is displayed on the bottom of screen if a password entry error occurs and changed the password again in the above method. Turning it by more than 3 times will completely escape from the setup menu.

¥The changed setting value is stored if pressing the “SET” button and you can return to the main menu.

✴“X” is displayed on screen when entering password.

5-11

Image 49

Contents Digital Multiplexer Digital Multiplexer SDM 090P Do Not Expose This Equipment To Rain or Moisture Important Safeguards Digital Multiplexer SDM-090P Digital Multiplexer SDM-090P Contents Viii Occurrence and Handling of Alarm Chapter Introduction IntroductionPage Multi Screen Name of parts and FunctionREC Check TriplexList RESET/ERASEMenu EnterRear Panel VCR IN/OUT BNC Installation Physical & Environmental Preparing for the InstallationPrecautions when Installing 15Cm Digital Multiplexer SDM-090P Unpacking Connecting to Other Devices Connecting to normal VCR and Monitor Connecting to Other DevicesConnecting to S-VHS VCR and S-VHS Monitor Connecting to Time Lapse VCR Connecting to Alarm Sensor 2TXDTRANSMITTEDDATA 3RXDRECEIVEDDATA 5SGSIGNALGROUND Remote Control by connecting to PCPIN Number Ascii Multi Screen REC CHECK/PB Through LIVE/PB Triplex PIP ResetCH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9Chapter Setup a recording channel Turn on power switchChange it to a desiring indication mode Initial operationWhen desiring to see in the Triplex screen When desiring to see in the live screen/replay screenWhen desiring to see in the Full screen When desiring to see in the division screen When desiring to see automatic sequential conversion screen Freeze setting of Full screen When desiring to see the stop screenWhen desiring to see in the PIP screen When desiring to see in the zoom screenFull Mode When desiring to see output of VCR as it is When desiring to see in the record screenSetting of Program Menu REC OUT SET REC Type TLV Record setting of each cameraDuty SET Reservation OFF REC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 REC Type NOR ↔ TLVSetting of display mode ALL Sequence Loss Detect Loss Info Alarm InfoPB Display ALL Spot OUT Cvbs PIP Size Alarm S/W Time CH1 02 CH2 CH3 02 CH4 CH5 02 CH6 CH7 02 CH8 CH9 SequenceTitle SET Setting of title by channelYY/MM/DD MM/DD/YY DD/MM/YY 01/04/01 123001 YY/MM/DD Hhmmss DATE/TIME SET Display TypeAlarm SET Hold Time Setting of alarmREC Type NOR Alarm Input OFF REC Type NOR ↔ TLPassword Change System settingAlarm Buzzer OFF Loss Buzzer Summer Time System SET Baud RatePassword Change Password Check NEW Password Confirm +++++++++++++++++ + - - - - + Recording Digital Multiplexer SDM-090P Frame Normal record modeWeight value REC Duty record Time Lapse record modeReservation record Alarm weight value recordREC Duty Alarm, loss Digital Multiplexer SDM-090P Alarm release Alarm occurrence conditionsAlarm record Screen conversionVCR Trig Alarm signal standardALARM/LOSS List YY/MM/DD Hhmmss Alarm/Loss list referenceOperation in video loss Appendix a Appendix a Specifications Auto Switcher Outside Drawing Appendix B Appendix B Checking points in trouble When S-VHS record is not performed

Related manuals

Manual 41 pages 18.63 Kb