Samsung SDM-090P, SDM-090MP manual Preparing for the Installation, Physical & Environmental

Page 18

Digital Multiplexer SDM-090(P)

CHAPTER 2. INSTALLATION

Preparing for the Installation

The following information is prepared for safe installation of the unit.

This unit can be placed on a flat table or installed in the rack. It should not be

used vertically or skew, but horizontally. The location of the unit and the

composition of wiring are very important in properly operating the system. When

equipment is placed too close or if ventilation is not properly done, system may

not work properly, and maintenance of the system may be difficult. In order to

prevent system failure and to reduce system shut-down by outside

environmental factors, air circulation in the system operating room, and the

cover of the unit must be fixed. Do not open the cover voluntarily because high

voltage within the unit may cause electric shock.

PHYSICAL & ENVIRONMENTAL

¥Operating Temperature : 0 °C to 40 °C

¥Maintenance Temperature : -20 °C to 60 °C

¥Operating Humidity : 20% to 85% (RH)

¥Maintenance Humidity : 20% to 95% (RH)

¥Power Supply : 100 ~ 240 VAC

¥Power Consumption : less than 13W

¥Frequency : 50/60 Hz

CAUTIONS

When system is operated, input voltage range must be within 10% of nominal voltage, and power consent should be grounded. Heating devices such as hair dryer, iron, refrigerator should not be used together. For safe power supply, AVR (Automatic Voltage Regulator) is recommended.

The connector linked to this equipment can affect EMI,so it is recommended to coil the CORE-FERRITE for use.

2-1

Image 18

Contents Digital Multiplexer Digital Multiplexer SDM 090P Do Not Expose This Equipment To Rain or Moisture Important Safeguards Digital Multiplexer SDM-090P Digital Multiplexer SDM-090P Contents Viii Occurrence and Handling of Alarm Chapter Introduction IntroductionPage REC Check Name of parts and FunctionMulti Screen TriplexMenu RESET/ERASEList Enter Rear Panel VCR IN/OUT BNC Installation Preparing for the Installation Physical & EnvironmentalPrecautions when Installing 15Cm Digital Multiplexer SDM-090P Unpacking Connecting to Other Devices Connecting to Other Devices Connecting to normal VCR and MonitorConnecting to S-VHS VCR and S-VHS Monitor Connecting to Time Lapse VCR Connecting to Alarm Sensor Remote Control by connecting to PC 2TXDTRANSMITTEDDATA 3RXDRECEIVEDDATA 5SGSIGNALGROUNDPIN Number CH1 CH2 CH3 Multi Screen REC CHECK/PB Through LIVE/PB Triplex PIP ResetAscii CH4 CH5 CH6 CH7 CH8 CH9Chapter Change it to a desiring indication mode Turn on power switchSetup a recording channel Initial operationWhen desiring to see in the live screen/replay screen When desiring to see in the Triplex screenWhen desiring to see in the Full screen When desiring to see in the division screen When desiring to see automatic sequential conversion screen When desiring to see the stop screen Freeze setting of Full screenWhen desiring to see in the zoom screen When desiring to see in the PIP screenFull Mode When desiring to see in the record screen When desiring to see output of VCR as it isSetting of Program Menu Record setting of each camera REC OUT SET REC Type TLVDuty SET Reservation OFF REC Type NOR ↔ TLV REC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9Setting of display mode Sequence Loss Detect Loss Info Alarm Info ALLPB Display ALL Spot OUT Cvbs PIP Size Alarm S/W Time Sequence CH1 02 CH2 CH3 02 CH4 CH5 02 CH6 CH7 02 CH8 CH9Setting of title by channel Title SETDATE/TIME SET Display Type YY/MM/DD MM/DD/YY DD/MM/YY 01/04/01 123001 YY/MM/DD HhmmssREC Type NOR Alarm Input OFF Setting of alarmAlarm SET Hold Time REC Type NOR ↔ TLAlarm Buzzer OFF Loss Buzzer Summer Time System settingPassword Change System SET Baud RatePassword Change Password Check NEW Password Confirm +++++++++++++++++ + - - - - + Recording Digital Multiplexer SDM-090P Normal record mode FrameTime Lapse record mode Weight value REC Duty recordAlarm weight value record Reservation recordREC Duty Alarm, loss Digital Multiplexer SDM-090P Alarm record Alarm occurrence conditionsAlarm release Screen conversionAlarm signal standard VCR TrigAlarm/Loss list reference ALARM/LOSS List YY/MM/DD HhmmssOperation in video loss Appendix a Appendix a Specifications Auto Switcher Outside Drawing Appendix B Appendix B Checking points in trouble When S-VHS record is not performed

Related manuals

Manual 41 pages 18.63 Kb