Samsung SDM-090MP, SDM-090P Setting of alarm, Alarm SET Hold Time, REC Type NOR Alarm Input OFF

Page 47

Digital Multiplexer SDM-090(P)

5. Setting of alarm

Set operation when alarm occurs.

The following screen is displayed if pressing the “ENTER” button with the blinking indication placed at the “5.ALARM SET” by pressing the “MOVE” button on the main menu screen:

[ALARM SET]

HOLD TIME	01	MIN
	00	SEC
REC TYPE	NOR

ALARM INPUT OFF

- The blinking character moves if pressing →“ ”, “→” button.

-The setting value is changed if pressing “ →”, “→” button. HOLD TIME : 00 ~ 30 (MIN)

00 ~ 59 (SEC)

✴The 00 MIN 00 SEC means a manual mode (perform operation for the time the alarm

input enters into).

REC TYPE: NOR ↔ TL V

¥Set a record mode when alarm occurs. ALARM INPUT: OFF ↔ N.O ↔ N.C ↔OFF

¥Set according to the output of alarm sensor connected to the alarm input terminal on the rear side of this unit.

¥OFF: When no alarm input exists.

¥N.O: When alarm input is ACTIVE LOW.

¥N.C: When alarm input is ACTIVE HIGH.

-The changed setting value is stored if pressing the “SET” button and you can return to the main menu.

5-9

Image 47

Contents Digital Multiplexer Digital Multiplexer SDM 090P Do Not Expose This Equipment To Rain or Moisture Important Safeguards Digital Multiplexer SDM-090P Digital Multiplexer SDM-090P Contents Viii Occurrence and Handling of Alarm Chapter Introduction IntroductionPage Triplex Name of parts and FunctionMulti Screen REC CheckEnter RESET/ERASEList MenuRear Panel VCR IN/OUT BNC Installation Physical & Environmental Preparing for the InstallationPrecautions when Installing 15Cm Digital Multiplexer SDM-090P Unpacking Connecting to Other Devices Connecting to normal VCR and Monitor Connecting to Other DevicesConnecting to S-VHS VCR and S-VHS Monitor Connecting to Time Lapse VCR Connecting to Alarm Sensor PIN Number Remote Control by connecting to PC2TXDTRANSMITTEDDATA 3RXDRECEIVEDDATA 5SGSIGNALGROUND CH4 CH5 CH6 CH7 CH8 CH9 Multi Screen REC CHECK/PB Through LIVE/PB Triplex PIP ResetAscii CH1 CH2 CH3Chapter Initial operation Turn on power switchSetup a recording channel Change it to a desiring indication modeWhen desiring to see in the Full screen When desiring to see in the live screen/replay screenWhen desiring to see in the Triplex screen When desiring to see in the division screen When desiring to see automatic sequential conversion screen Freeze setting of Full screen When desiring to see the stop screenFull Mode When desiring to see in the zoom screenWhen desiring to see in the PIP screen When desiring to see output of VCR as it is When desiring to see in the record screenSetting of Program Menu Duty SET Reservation OFF Record setting of each cameraREC OUT SET REC Type TLV REC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 REC Type NOR ↔ TLVSetting of display mode PB Display ALL Spot OUT Cvbs PIP Size Sequence Loss Detect Loss Info Alarm InfoALL Alarm S/W Time CH1 02 CH2 CH3 02 CH4 CH5 02 CH6 CH7 02 CH8 CH9 SequenceTitle SET Setting of title by channelYY/MM/DD MM/DD/YY DD/MM/YY 01/04/01 123001 YY/MM/DD Hhmmss DATE/TIME SET Display TypeREC Type NOR ↔ TL Setting of alarmAlarm SET Hold Time REC Type NOR Alarm Input OFFSystem SET Baud Rate System settingPassword Change Alarm Buzzer OFF Loss Buzzer Summer TimePassword Change Password Check NEW Password Confirm +++++++++++++++++ + - - - - + Recording Digital Multiplexer SDM-090P Frame Normal record modeWeight value REC Duty record Time Lapse record modeREC Duty Alarm weight value recordReservation record Alarm, loss Digital Multiplexer SDM-090P Screen conversion Alarm occurrence conditionsAlarm release Alarm recordVCR Trig Alarm signal standardALARM/LOSS List YY/MM/DD Hhmmss Alarm/Loss list referenceOperation in video loss Appendix a Appendix a Specifications Auto Switcher Outside Drawing Appendix B Appendix B Checking points in trouble When S-VHS record is not performed

Related manuals

Manual 41 pages 18.63 Kb