Tripp Lite SRXCOOL12K, SRCOOL12K owner manual Operation

Page 8

Operation

Warning: Install the unit according to the instructions in the “Installation” section before attempting to operate it.

Power

Turn the unit on or off by pressing the “POWER” button.

The unit has a three-minute compressor delay in order to prevent potential circuit overloads at start up.

Automatic Restart Feature

The unit will turn on and resume operation automatically when power is restored after a power outage. The unit will use the same settings that it used immediately before the power outage occurred. Note: If the power outage is brief, the unit will run the fan alone for three minutes before resuming normal operation. The delay allows the compressor to depressurize so the unit will function properly when it enters Cool mode.

Cool Mode

Pressing the “FUNCTION” button cycles between Cool mode and Dehumidify mode. The “COOLING” LED illuminates when Cool mode is active.

Press the TEMP+ and TEMP- buttons to set the temperature in Cool mode. The selected temperature is shown on the numeric display. Once set, the desired temperature will blink five times after which the display will show the current room temperature.

Press the “FAN SPEED” button to cycle between high, medium and low fan speeds. An LED illuminates to indicate the selected fan speed. When speed is set on AUTO, the unit will automatically select a fan speed based on the set and ambient temperatures. If ambient temperature is lower than the set temperature, the fan will run and the “COOLING” LED will blink to indicate that the compressor is off. When cooling resumes, the “COOLING” LED will remain illuminated.

Dehumidify Mode

Pressing the “FUNCTION” button cycles between Cool mode and Dehumidify mode.

The “DEHUMIDIFY” LED illuminates when Dehumidify mode is active. In Dehumidify mode, the fan runs at a fixed speed and temperature controls are irrelevant. For optimal performance

in Dehumidify mode, close windows and doors, remove the top drain plug and route user- supplied drain line to external drainage.

Timer

The “TIMER” button allows you to schedule the unit to turn on or off automatically.

Timer On (Note: The unit must be off to activate the Timer On function. Confirm that mode, temperature and fan speed settings are correct before activating the Timer On function.) Activate the timer by pressing the “TIMER” button. Press the TEMP+ and TEMP- buttons to set the delay (in hours) before the unit will turn on. The number of hours is shown on the numeric display. The number will flash on the screen five times before returning to the current temperature.

Timer Off (Note: The unit must be on to activate the Timer Off function.) Activate the timer by pressing the “TIMER” button. Press the TEMP+ and TEMP- buttons to set the delay (in hours) before the unit will turn off. The number of hours is shown on the numeric display. The number will flash on the screen five times before returning to the current temperature.

Quiet Control Mode

The unit includes a Quiet Control mode which regulates the cooling via the timer and microprocessor to achieve quieter operation levels when noise is an issue.

To activate, press the “QUIET” button. The Quiet LED will turn on. Set the desired temperature and then set the timer to the duration of the Quiet Control mode cycle. During the course of the cycle, the microprocessor memory will adjust the preset temperature by 0.9°F (0.5°C) every 30 minutes until it reaches the desired temperature. Once the temperature is reached, the unit will maintain the temperature for the duration of the set time.

Changing Degree Units

The unit can display temperature in both Celsius and Fahrenheit. The default setting for the SRCOOL12K is Fahrenheit and the SRXCOOL12K is Celsius.

To toggle between temperature modes, put the unit in standby mode. The air conditioner is in standby mode when it is plugged into live AC power, but powered off. Then, hold the “FUNCTION” key for 10 seconds until a beep sounds.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Portable Air Conditioning Unit SRCOOL12K 120 V, 60 Hz SRXCOOL12K 230V, 50 HzRecommended Applications Important Safety InstructionsIntroduction Control Panel FeaturesFront View Installation Accessory Parts ListUnit Placement Cooling Duct Connection OptionalExhaust Duct Connection After completing , proceed to step Drop Ceiling Exhaust ConnectionWindow Exhaust Connection Low Temperature Operation 1Cooling Mode with Re-Evaporation2Cooling Mode without Re-Evaporation 3Dehumidify ModeOperation Maintenance TroubleshootingAlarm Cleaning the Air FiltersStorage and Service Warranty and Warranty RegistrationAdditional Display Error Codes ServiceManual del Propietario SRCOOL12K 120V, 60 Hz SRXCOOL12K 230V, 50 HzIntroducción Instrucciones de seguridad importantesAplicaciones Recomendadas AdvertenciasPanel de Control CaracterísticasVista Frontal Instalación Lista de Piezas AccesoriasUbicación de Unidad Conexión del Ducto de Enfriamiento OpcionalConexión del Ducto de Descarga Después de terminar el paso 4 , proceda al paso Conexión de Descarga de Falso PlafónConexión de Descarga de Ventana Inserción del Tapón de Drenaje Operación a Baja Temperatura1Modo de Enfriamiento con Re-evaporación 2Modo de Enfriamiento sin Re-evaporaciónFuncionamiento Solución de Problemas AlarmaMantenimiento Limpieza de los Filtros de AireCódigos Adicionales de Error de Pantalla Almacenamiento y servicioGarantía y Registro de Garantía AlmacenamientoManuel du propriétaire SRCOOL12K 120 V, 60 Hz SRXCOOL12K 230V, 50 HzAvertissements Applications recommandéesConsignes de sécurité importantes Vue de face Panneau de commandeCaractéristiques Connexion du conduit de refroidissement en option Liste des pièces accessoiresDisposition de l’appareil Installation suite Connexion du conduit d’évacuationConnexion de l’évacuation à un faux-plafond Après avoir complété l’étape 4 , passez à l’étapeInsertion du bouchon d’évacuation Fonctionnement à basse température1Mode de refroidissement avec évaporation 2Mode de refroidissement sans évaporationFonctionnement Alarme DépannageChangement des unités de température Nettoyage des filtres à airEntreposage et service Garantie et enregistrement de la garantieCodes d’erreur d’affichage supplémentaires EntreposageРуководство пользователя SRCOOL12K 120 В, 60 Гц SRXCOOL12K 230 В, 50 ГцПредупреждения ВведениеВажные указания по технике безопасности Вид спереди Панель управленияУстановка Перечень комплектующихРазмещение устройства Подсоединение воздуховода охлаждения опциональноПодсоединение вытяжного воздуховода Установка продолжениеПроводка вытяжного воздуховода через подвесной потолок Вытяжка через окноДля всех вариантов применения По завершении шага 4 , переходите к шагуУстановка сливной пробки Работа при низких температурах1Режим охлаждения с повторным испарением 2Режим охлаждения без повторного испаренияЭксплуатация Выявление и устранение неисправностей Эксплуатация продолжениеТехническое обслуживание Выявление и устранение неисправностей продолжение Хранение и техническое обслуживаниеГарантийные обязательства и регистрация гарантии Коды ошибок, выводимые на дисплей
Related manuals
Manual 8 pages 38.72 Kb

SRCOOL12K, SRXCOOL12K specifications

The Tripp Lite SRXCOOL12K and SRCOOL12K portable air conditioners are designed for those seeking an efficient cooling solution for small to medium-sized spaces. These units are particularly popular in server rooms, offices, and other environments where heat output can be an issue. Both models share several key features and characteristics that make them stand out in the portable cooling market.

One of the main features of the Tripp Lite SRXCOOL12K is its powerful cooling capability. With a cooling capacity of 12,000 BTU, the unit can effectively cool areas up to 400 square feet. This makes it suitable for a variety of applications, from temporary cooling in commercial settings to long-term solutions for home offices or server equipment. The unit also operates quietly, which is beneficial for environments where distractions need to be minimized.

The SRXCOOL12K and SRCOOL12K both utilize advanced technologies that enhance their performance and ease of use. The self-evaporative design allows for efficient cooling while minimizing the need for manual drainage. The units can drain moisture as water vapor, reducing the frequency of maintenance and ensuring consistent performance. This technology helps maintain compact size and mobility while keeping energy consumption in check.

Convenience is another significant characteristic of these models. The included remote control allows users to adjust settings from a distance, providing added flexibility. With multiple cooling settings and fan speeds, users can customize their cooling experience according to their specific needs or preferences. Moreover, the energy-saving mode is particularly useful for those looking to reduce electricity costs while still enjoying a comfortable environment.

The Tripp Lite SRXCOOL12K and SRCOOL12K are also designed with user-friendly installation in mind. Their compact and portable designs make them easy to move between rooms or locations, and the included window installation kit facilitates straightforward setup in various window types.

In summary, the Tripp Lite SRXCOOL12K and SRCOOL12K offer an effective solution for cooling needs with their robust cooling capacities, self-evaporative technology, and user-friendly features. Ideal for both commercial and residential applications, these portable air conditioners provide dependable performance, convenience, and energy-efficiency for any space that requires reliable cooling.
Top Page Image Contents