Samsung SDM-160N manual Connecting to Other Devices, Connecting to normal VCR and Monitor

Page 14

Digital Multiplexer

CHAPTER 3. Connecting to Other Devices

This unit can be connected to other devices such as monitor, camera, VCR, and PC. This chapter describes how to connect the unit to other devices.

CAUTIONS

Be sure that voltages higher than 2 VDC should not be input to the input terminal of Camera and Video.

1. Connecting to normal VCR and Monitor

When connecting to a normal VCR, Select ‘NOR’ in “REC TYPE” of “1. REC OUT SET” in SETUP MENU.

1. Connect a BNC cable to the VCR IN terminal on the Unit Rear Panel and to the OUT termi- nal of the VCR.

2. Connect a BNC cable to the VCR OUT termi- nal on the Unit Rear Panel and to the IN termi- nal of the VCR.

3. Connect a BNC cable to the MON OUT termi- nal on the Unit Rear Panel and to the IN termi- nal of the Monitor.

2. Connecting to S-VHS VCR and S-VHS MONITOR

When playing back TAPE by connecting to S- VHS, select “Y/C” in “PB IN” Mode, once you in “2.MON OUT SET” Mode in SETUP Menu. 1. Connect a S-JACK cable to the VCR IN 4- pin terminal on the Unit’s Rear Panel and to

the OUT terminal on the VCR.

2. Connect a S-JACK cable to the VCR OUT 4-pin terminal on the Unit’s Rear Panel and to the IN terminal on the VCR.

3. Connect a S-JACK cable to the MON OUT 4-pin terminal on the Unit’s Rear Panel and to the IN terminal on the Monitor.

✴SDM-160M/SDM-160MP:Not used.

3-1

Image 14

Contents Digitalmultiplexer Graphic Symbol Explanation Digital MultiplexerIii Contents Appendix B Checking Points in Trouble Introduction IntroductionName of parts and Function Move → With RS-485 cable, Remote Control can be done Indicates terminal for connecting to VCR Input/OutputWith RS-232C cable, Remote Control can be done Connects to Power CordPreparing for the Installation Physical & EnvironmentalPrecautions when Installing Page Unpacking Connecting to S-VHS VCR and S-VHS Monitor Connecting to Other DevicesConnecting to normal VCR and Monitor OUT terminal on the VCRConnecting to Time Lapse VCR Connecting to Alarm Sensor CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 Remote Control by connecting to PCAscii Ascii AautoMON button → Address + 1 input → Enter Remote Control using SSC-1000RS-485Monitor OUT Control Spot OUT ControlBasic Method to use When desiring to see in the live screen/replay screenWhen desiring to see in the Triplex screen Initial operationWhen desiring to see in the Full screen When desiring to see in the division screenWhen desiring to see automatic sequential conversion screen Full Mode When desiring to see the stop screenWhen desiring to see in the zoom screen When desiring to see output of VCR as it is When desiring to see in the PIP screenWhen desiring to see in the record screen REC OUT SET Type TLV Setting of Program MenuRecord setting of each camera Duty SET Reservation OFFEND Time REC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9REC Reservation Start Time ALL Setting of display modeSequence Loss Detect Loss Info Alarm Info Motion Info PB Display ALL Spot OUT Cvbs PIP SizeAlarm S/W Time SequenceBlinking character moves if pressing →, → button Setting of title by channelYou can set of each channel Enter button at a position desired to set titleDATE/TIME SET Display Type Title SETIjklmnopqrstuvwxyz Setting of alarm Setting of motionXxxxxxxxxxx Password Check OFF Alarm Buzzer Loss Buzzer Summer Time System settingPassword Change Baud RateIs displayed on screen when entering password Password Change Password Check NEW Password ConfirmEnter the current password in order Recording Normal record modeTime Lapse record mode Reservation record Weight value REC Duty recordAlarm weight value record REC DutyAlarm record Alarm occurrence conditionsAlarm release Alarm signal standardOperation in motion detection Alarm/Loss list referenceOperation in video loss Appendix a Specifications Outside Drawing Ensure power cord is properly inserted Appendix B Checking points in trouble