Samsung SDM-160N manual Setting of alarm, Setting of motion

Page 30

Digital Multiplexer

5. Setting of alarm

Set operation when alarm occurs.

The following screen is displayed if pressing the “ENTER” button with the blinking indication placed at the “5.ALARM SET” by pressing the “MOVE” button on the main menu screen:

[ALARM SET]

HOLD TIME	01	MIN
	00	SEC
REC TYPE	NOR

ALARM INPUT OFF

→→

-The blinking character moves if pressing “ ”, “ ” button.

-The setting value is changed if pressing “→ ”, “→ ” button.

HOLD TIME : 00 ~ 30 (MIN) 00 ~ 59 (SEC)

✴The 00 MIN 00 SEC means a manual mode (perform operation for the time the alarm input enters into).

REC TYPE: NOR ↔ TL V

•Set a record mode when alarm occurs. ALARM INPUT: OFF ↔ N.O ↔ N.C ↔ OFF

•Set according to the output of alarm sensor connected to the alarm input terminal on the rear side of this unit.

•OFF: When no alarm input exists.

•N.O: When alarm input is ACTIVE LOW.

•N.C: When alarm input is ACTIVE HIGH.

- The changed setting value is stored if pressing the “SET” button and you can return to the main menu.

6. Setting of motion

Set motion detection and operation.

The following screen is displayed if pressing the “ENTER” button with the blinking indication placed at the “6.MOTION SET” by pressing the “MOVE” button on the main menu screen:

[MOTION SET]

SENSITIVITY		OFF
AREA	SET	CH1...
MOTION OUT		OFF
LIST	UPDATE	OFF
BUZZER		OFF

5-7

Image 30

Contents Digitalmultiplexer Graphic Symbol Explanation Digital MultiplexerIii Contents Appendix B Checking Points in Trouble Introduction IntroductionName of parts and Function Move → With RS-485 cable, Remote Control can be done Indicates terminal for connecting to VCR Input/OutputWith RS-232C cable, Remote Control can be done Connects to Power CordPreparing for the Installation Physical & EnvironmentalPrecautions when Installing Page Unpacking Connecting to S-VHS VCR and S-VHS Monitor Connecting to Other DevicesConnecting to normal VCR and Monitor OUT terminal on the VCRConnecting to Time Lapse VCR Connecting to Alarm Sensor CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 Remote Control by connecting to PCAscii Ascii AautoMON button → Address + 1 input → Enter Remote Control using SSC-1000RS-485Monitor OUT Control Spot OUT ControlBasic Method to use When desiring to see in the live screen/replay screenWhen desiring to see in the Triplex screen Initial operationWhen desiring to see in the Full screen When desiring to see in the division screenWhen desiring to see automatic sequential conversion screen When desiring to see the stop screen When desiring to see in the zoom screenFull Mode When desiring to see in the PIP screen When desiring to see in the record screenWhen desiring to see output of VCR as it is REC OUT SET Type TLV Setting of Program MenuRecord setting of each camera Duty SET Reservation OFFREC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 REC Reservation Start TimeEND Time ALL Setting of display modeSequence Loss Detect Loss Info Alarm Info Motion Info PB Display ALL Spot OUT Cvbs PIP SizeAlarm S/W Time SequenceBlinking character moves if pressing →, → button Setting of title by channelYou can set of each channel Enter button at a position desired to set titleTitle SET IjklmnopqrstuvwxyzDATE/TIME SET Display Type Setting of alarm Setting of motionXxxxxxxxxxx Password Check OFF Alarm Buzzer Loss Buzzer Summer Time System settingPassword Change Baud RatePassword Change Password Check NEW Password Confirm Enter the current password in orderIs displayed on screen when entering password Normal record mode Time Lapse record modeRecording Reservation record Weight value REC Duty recordAlarm weight value record REC DutyAlarm record Alarm occurrence conditionsAlarm release Alarm signal standardAlarm/Loss list reference Operation in video lossOperation in motion detection Appendix a Specifications Outside Drawing Ensure power cord is properly inserted Appendix B Checking points in trouble