Samsung SDM-160N Indicates terminal for connecting to VCR Input/Output, Connects to Power Cord

Page 9

Digital Multiplexer

Rear panel

ENGLISH

F G H A IBE C DJ

A. CAMERA INPUT / LOOP THROUGH OUT

-Up to 16 camera signals can be input. When transmitting camera signals to external devices, OUT terminal can be used.

B.ALARM IN / ALARM OUT / VTI TERMINAL

-VTI: TRIGGER Output Connection terminal of VCR

-ALARM IN: Up to 16 ALARM Sensors can be connected. “G” indicates grounding terminal connect- ed to ALARM Input, and should be connected to grounding terminal of sensors.

-ALARM OUT (HOT/COLD): When ALARM is activated, ACTIVE MAKE Signal is generated.

-ALARM RESET : Connected to RESET terminal of VCR, and when ALARM is deactivated, PULSE is generated.

-MOTIOM OUT(M/O) : When MOTION is activated, ACTIVE MAKE signal is generated.

C.VCR IN/OUT (BNC)

Indicates terminal for connecting to VCR Input/Output.

D. MONITOR OUT (BNC)

Indicates terminal for connecting to Monitor’s video Input terminal.

E. SPOT OUT (BNC)

Indicates terminal for connecting to Monitor’s video Input terminal.

F. VCR IN/OUT (4PIN MINI DIN)

Indicates terminal for connecting to VCR’s S-VHS Input/Output terminal.

✴SDM-160M/SDM-160MP:Not used.

G.MONITOR OUT (4PIN MINI DIN)

Indicates terminal for connecting to Monitor’s video S-VHS Input terminal.

✴ SDM-160M/SDM-160MP:Not used.

H.RS-232C

With RS-232C cable, Remote Control can be done.

I. RS-485

With RS-485 cable, Remote Control can be done.

J. ~AC IN

Connects to Power Cord.

1-4

Image 9

Contents Digitalmultiplexer Digital Multiplexer Graphic Symbol ExplanationIii Contents Appendix B Checking Points in Trouble Introduction IntroductionName of parts and Function Move → With RS-232C cable, Remote Control can be done Indicates terminal for connecting to VCR Input/OutputWith RS-485 cable, Remote Control can be done Connects to Power CordPhysical & Environmental Preparing for the InstallationPrecautions when Installing Page Unpacking Connecting to normal VCR and Monitor Connecting to Other DevicesConnecting to S-VHS VCR and S-VHS Monitor OUT terminal on the VCRConnecting to Time Lapse VCR Connecting to Alarm Sensor Ascii Remote Control by connecting to PCCH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 Ascii AautoMonitor OUT Control Remote Control using SSC-1000RS-485MON button → Address + 1 input → Enter Spot OUT ControlWhen desiring to see in the Triplex screen When desiring to see in the live screen/replay screenBasic Method to use Initial operationWhen desiring to see in the division screen When desiring to see in the Full screenWhen desiring to see automatic sequential conversion screen When desiring to see the stop screen When desiring to see in the zoom screenFull Mode When desiring to see in the PIP screen When desiring to see in the record screenWhen desiring to see output of VCR as it is Record setting of each camera Setting of Program MenuREC OUT SET Type TLV Duty SET Reservation OFFREC Duty SET CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 REC Reservation Start TimeEND Time Sequence Loss Detect Loss Info Alarm Info Motion Info Setting of display modeALL PB Display ALL Spot OUT Cvbs PIP SizeSequence Alarm S/W TimeYou can set of each channel Setting of title by channelBlinking character moves if pressing →, → button Enter button at a position desired to set titleTitle SET IjklmnopqrstuvwxyzDATE/TIME SET Display Type Setting of motion Setting of alarmXxxxxxxxxxx Password Change System settingPassword Check OFF Alarm Buzzer Loss Buzzer Summer Time Baud RatePassword Change Password Check NEW Password Confirm Enter the current password in orderIs displayed on screen when entering password Normal record mode Time Lapse record modeRecording Alarm weight value record Weight value REC Duty recordReservation record REC DutyAlarm release Alarm occurrence conditionsAlarm record Alarm signal standardAlarm/Loss list reference Operation in video lossOperation in motion detection Appendix a Specifications Outside Drawing Appendix B Checking points in trouble Ensure power cord is properly inserted