Samsung AR10NVFSCURNSV manual Troubleshooting

Page 22

Cleaning and Maintenance

Troubleshooting

If the air conditioner operates abnormally, refer to the following chart to save time and unnecessary expenses.

	Problem	Solution

		• Check the power status, then operate the air conditioner again.
		• Switch on the circuit breaker, plug in the power cord, then operate the
	The air conditioner does	air conditioner again.
	not work at all.	• Make sure that the isolator is turned on.
		• Check whether the Timed off function is running. Operate the air
		conditioner again by pressing the Power button.

	I cannot change the	• Check whether the Fan or Fast mode is running. In these modes, the air
	I cannot change the	conditioner controls the set temperature automatically, and you cannot
	temperature.
	temperature.	change the set temperature.
		change the set temperature.

		• Check whether the set temperature is higher in the Cool mode than
		the current temperature. Press the Temperature button on the remote
		control to change the set temperature.
		• Check whether the air filter is blocked with dirt. If the air filter is
		blocked, the cooling performance may decrease. Remove dirt regularly.
		• Check whether the outdoor unit is covered or installed near obstacles.
	Cool air does not come out	Remove the coverings and obstacles..
	Cool air does not come out	• Check whether doors or windows are open. This may cause poor
	of the air conditioner.
	of the air conditioner.	cooling performance. Close the doors and windows.
		cooling performance. Close the doors and windows.
		• Check whether the air conditioner is turned on immediately after the
		cooling operation stops. In this case, only the fan runs to protect the
		outdoor unit compressor.
		• Check whether the pipe length is too long. When the pipe length
		exceeds the maximum pipe length, the cooling performance may
		decrease.

	I cannot change the air flow	• Check whether the good'sleep function is running. While this function
	direction.	is running, you cannot control the air flow direction.

	I cannot change the fan	• When the Auto, Dry, or Fast mode is running or the good'sleep function
	I cannot change the fan	is running in the Cool mode, the air conditioner controls the fan speed
	speed.
	speed.	automatically and you cannot change the fan speed.
		automatically and you cannot change the fan speed.

		• Replace the batteries in the remote control with new ones.
	The remote control does	• Make sure that nothing is blocking the remote control sensor.
	The remote control does	• Check whether there are strong lighting apparatus near the air
	not work.
		conditioner. Strong light which comes from fluorescent bulbs or neon
		signs may interrupt the electric waves.

22English

Image 22

Contents Air conditioner Contents Correct disposal of batteries in this product Failing to do so may result in electric shock or fire Safety InformationThis may result in electric shock or fire For Power Supply This may result in electric shock or burns Do not touch the circuit breakerwith wet handsThis may result in electric shock This may result in children seriously injuring themselvesDo not operate the appliance with wet hands Do not clean the inside of the air conditioner by yourselfDo not drink the water from the air conditioner Indoor Unit Overview Timer indicatorOperation indicator DisplayRemote Control Overview Inserting batteriesControlling temperature Remote Control OperationOperation modes Controlling air flow direction Controlling fan speedHorizontal air flow manual Cooling Operation Cool modeStep cooling function Dry mode Dehumidifying OperationAuto mode Quick Smart FeaturesFan mode Fast function Comfort functionQuiet function Beep sound functionEnergy-Saving Operation Cool mode When the Single user function starts,Button Cool mode Select Single user Single user functionTimed on/Timed off function Good’sleep function Cleaning duration Minutes Cleaning at a GlanceRunning Auto clean Do not clean the display by using alkaline detergentCleaning the filter Troubleshooting Check whether the drains are clean. Clean them regularly Problem Solution Timed on/offFunction does not work Setting the time Indicator blinks An error is indicatedInstallation of the unit General informationPower supply line, fuse, or circuit breaker Install the unit in a place where water can drain smoothlyMinimum clearances for the outdoor unit Choosing the installation locationCases Unpacking Checking and preparing accessories and toolsAccessories Unpacking the indoor unitAccessories in the outdoor unit package Optional accessoriesTools Taping the pipes, cables, and drain hose Drilling a hole through the wallIndoor Unit Installation Prepare the following tools Optional Extending the power cableApply heat to the contraction tube to contract it Install the drain hose Installing and connecting the drain hoseOptional Extending the drain hose Optional Changing the direction of the drain hose Shortening or extending the refrigerant pipes assembly pipe When fixing the indoor unit on a wall Fixing the installation plateWhen fixing the indoor unit on a window frame When fixing the indoor unit on a gypsum board Fix the installation plate without inclining to one sideFixing the outdoor unit in place Outdoor Unit InstallationPipes Optional Fixing the outdoor unit to a wall with a rackEvacuating the air Adding refrigerant RefrigerantRunning the Smart Install mode Installation InspectionPerforming the gas leak tests Off, Blinking, On LEDPerforming final check and trial operation Press the Power button to stop the trial operationPumping down for removing the product English English Questions or COMMENTS?