Heatiator NNXT4236IL NNXT3933I, NNXT3933IL owner manual NNXT4236I, NNXT4236IL

Page 79

C. Service Parts (continued)

NNXT4236I, NNXT4236IL



IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for				Stocked
your appliance please provide model number and serial number. All parts listed in this manual may				Stocked
be ordered from an authorized dealer.				at Depot
				at Depot
ITEM	DESCRIPTION	COMMENTS	PART NUMBER
	Log Assembly		4055-976	Y
1	Back Log		SRV4055-966
2	Bottom Right Log		SRV4055-967
3	Bottom Left Log		SRV4055-969
	Log Assembly, Top and Middle		SRV4055-974
4	Middle Right Log		SRV4055-970
5	Top Right Log		SRV4055-971
6	Middle Left Log		SRV4055-972
7	Top Left Log		SRV4055-973
8	Intake Cover Gasket		25844
9	Intake Cover Gasket		4031-239
10	Non Combustible Board		4055-895
11	Dry Wall Lip		4055-893
12	Hood		4055-215
13	Heater Bafﬂe		4055-881
14	Hearth Pan		4055-874
15	Valve Assembly		Refer to valve page.
16	Glass Frame Assembly		GLA4000-307	Y
17	Screen Assembly		SRV4055-991	Y
18	Floor Cover		4055-274
19	Burner Assembly NG		4055-882	Y
19	Burner Assemlby LP		4055-896	Y
	Burner Assemlby LP		4055-896	Y
20	Gasket Valve Plate		4055-135
21	Glass Latch Assembly	Pkg of 2	33858/2	Y
22	Magnetic Touch Latch	Qry 2 req	4021-650	Y
23	Junction Box		4021-013	Y
24	Cover Plate		4031-222
25	Junction Box Shield		4055-888
26	Nailing Flange	Qty 4 req	4044-161
27	Back Gasket		4000-225
	Cord Clip		14218
	Refractory, Back		4055-856
	Refractory, Right Side		4055-859
	Refractory, Left Side		4055-860
	Refractory, Top		4055-866
	Conversion Kit NG		DCKVN-NNXT	Y
	Conversion Kit LP		DCKVP-NNXT	Y
	Pilot Oriﬁce NG		593-528	Y
	Pilot Oriﬁce LP		593-527	Y
	Regulator NG		NGK-DXV-50	Y
	Regulator LP		LPK-DXV-50	Y

Additional service parts on following page.

Heatilator • Novus NNXT • 4055-879 • Rev. o • 2/12

79

Image 79

Contents Models Installation and OperationHomeowner Reference Information CongratulationsTable of Contents Finishing Limited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Operating Instructions Gas Fireplace SafetyYour Fireplace Clear Space Fixed Glass AssemblyRemote Controls, Wall Controls and Wall Switches Fan Kit optionalControl Module Operation IPI Battery Tray/Battery InstallationBefore Lighting Fireplace Final inspection by Lighting Instructions IPIInitial Break-in Procedure Frequently Asked QuestionsAfter Fireplace is Lit Maintenance Tasks-Homeowner Maintenance and ServiceMaintenance Tasks-Qualiﬁed Service Technician Typical Appliance System Getting StartedTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Select Appliance Location Framing and ClearancesConstruct the Appliance Chase In. to Level of Standoffs ClearancesMantels Mantel and Wall ProjectionsMantel Legs or Wall Projections Vent Termination Minimum Clearances Termination LocationsMinimum Clearances for Termination Use of Elbows Vent Information and DiagramsApproved Pipe Vent Table KeyTop Vent Horizontal Termination Vent DiagramsOne Elbow Two Elbows Two 45 Elbows replacing One 90 ElbowTions Top Vent Vertical TerminationThree Elbows No ElbowLower & twist pull out 12 ft 3.66 m min 60 ft 18.29 m max 12 ft 3.66 m min ft 18.29 m max One 45 Elbow Rear Vent Horizontal TerminationInstalled Horizontally Rear Vent Vertical Termination Min Ft 1.83 m max 12 ft 3.66 m min Combustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration FramingCeiling ﬁrestop Must be used between ﬂoors and attics Install the Ceiling FirestopFlat Ceiling Installation Install Attic Insulation ShieldVaulted Ceiling Installation Top Vent Appliance PreparationIt Cannot be changed at a later time Basket Rear Vent11 Proper Positioning and Securing of an Appliance Secure and Level the ApplianceAssemble Pipe Sections Install Vent PipeAttach Pipe to the Firebox Assembly Assemble Vent Sections DVP OnlyAssemble Slip Sections Assemble Vent Sections SLP OnlyDisassemble Vent Sections Secure the Vent SectionsInstall Decorative Ceiling Components SLP only Assemble and Install Storm Collar Install Metal Roof FlashingInstall Decorative Wall Components SLP only Install Vertical Termination CapHeat Shield Requirements for Horizontal Termination Failure to maintain overlap may cause overheating and ﬁre Install Horizontal Termination CapOpen Top Shroud may be used with DVP-TV, DVP-TVHW, SLP-TVHW ShroudsHHT Shrouds Field Constructed ShroudsMailbox Style Shroud Dimensions Min. Base Dims Gas Connection Gas InformationFuel Conversion Gas PressureElectrical Information Wiring RequirementsIntelliﬁre Plus Ignition System Wiring Optional Accessories RequirementsRC200 Wiring Diagram Electrical Service and RepairWall Switch Installation for Fan Optional Junction Box InstallationRC200 Remote Control Installation & OperationsInstallation of Remote Control Housing Programming the RC200 to the Control Module Power Outage Finishing Do not Remove Facing MaterialAppliance Setup Place the Lava Rock Clean the Appliance Assemble LogsAccessories Place the RockwoolAir Shutter Setting Replacing Fixed Glass AssemblyRemove Screen Protector Install HoodInstall Control Heat Shield Install the Control Heat ShieldInstall the ﬂoor cover as shown in Figure Install Floor CoverHang Screen on Shoulder Screws Close the Screen AssemblyIntelliﬁre Plus Intermittent Ignition System TroubleshootingIntelliﬁre Plus Intermittent Pilot Ignition System Reference Materials Appliance Dimension DiagramDVP45 Vent Components DiagramsDVP-TRAPFL 229 mm DVP-TRAP DVP-HRC-SS SLP Series Vent Components  B. Vent Components DiagramsSL-2DVP SLK-SNKD DVP-FBHT Service Parts Log Set AssemblyPart number list on following At Depot StockedNNXT4236I, NNXT4236IL #15 Valve Assembly #16 Ignition Control AssemblyOptional Components Do not Discard this Manual Contact Information