Desa CSG3930PR, CSG3930NR Installing Log #2 Right and Log #3 Left Model VRL30NR Shown

Page 16

16

INSTALLATION

Installing Logs (Cont.)

INSTALLATION

Continued

Models VRL24NR, VRL24PR, VRL30NR, VRL30PR, VRL24NT, VRL24PT, VRL30NT and VRL30PT

1.Place log #1 (ember bed) onto base over log alignment screws to the left of front burner and behind middle burner. Log #1 will sit on top of front and middle burners (see Figure 23).

2.Place log #2 to right of log #1 and onto log alignment screw as shown in Figure 24. Log #2 will wrap around right end of rear burner (see Figure 24).

3.Place log #3 on left side of base and onto alignment screw to right of rear burner (see Figure 24). Log #3 will wrap around left end of rear burner.

4.Place log #4 onto two alignment screws to rear of base (see Figure 25).

5.Locate hole on bottom of log #5 and place over pin on log #2. Log #5 will rest on back of log #1 (ember bed). See Figure 23 and 26.

6.Place log #6 onto two pins on log #1 (ember bed) and rest back of log #6 on back log #4 (see Figure 26).

Log #5 will seat in this location.

Log #1

Log #3

Log #2

Log #1

Figure 24 - Installing Log #2 (Right) and Log #3 (Left) (Model VRL30NR Shown)

Log #4

Log #3

Log #2

Log #1

Figure 25 - Installing Log #4 (Model VRL30NR Shown)

Log #6

Figure 23 - Installing Log #1 (Ember Bed) (Model VRL30NR

Shown)

Log #5

Log #4

Log #3

Log #2

Log #1

Figure 26 - Installing Log #5 and Log #6 (Model VRL30NR Shown)

For..com

110021-01G

Image 16
Contents OWNER’S Operation and Installation Manual What to do if YOU Smell GASTable of Contents Safety InformationSafety Information Optional Remote Control Accessories Product IdentificationLocal Codes UnpackingProduct Features AIR for Combustion and VentilationDetermining FRESH-AIR Flow for Heater Location Determining if You Have a Confined or Unconfined SpaceVentilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Installation and Clearances for VENT-FREE Operation InstallationCheck GAS Type Minimum Noncombustible Material Clearances See Between 8Determining Minimum Mantel Clearance When Using a Hood Mantel ClearancesFloor Clearances Determining Minimum Mantel ClearanceInstalling Damper Clamp Accessory for Vented Operation Installing Heater Base AssemblyInstallation Items Needed Remote-Ready Models OnlyConnecting to GAS Supply Attaching Base Assembly to Fireplace Floor 30 Model ShownExternal Regulator With Vent Pointing Down Pressure Testing Heater Gas Connections Pressure Testing gas Supply Piping systemChecking GAS Connections Installing Logs Installing Log #4 Model CSG3924NR ShownInstalling Log #2 Right and Log #3 Left Model VRL30NR Shown Attaching Grate to Base Assembly Operating HeaterAdding Lava Rock Lighting InstructionsManual Lighting Procedure To Turn OFF GAS To ApplianceThermostat Control Operation Shutting Off HeaterREMOTE-READY Models For Your Safety Read Before Lighting Optional HAND-HELD Remote Operation Control Knobs and Ignitor Button Locations ShownManual Mode Auto Thermostatic ModeSafety Features ON/OFF Series Models Ghrcb and CghrcbPilot Flame Pattern Inspecting BurnersBurner Flame Patterns Cleaning Burner Injector Holders and Pilot AIR Inlet Holes Cleaning MaintenanceLogs Troubleshooting Observed Problem Possible Cause RemedyRefer to Air for Combustion and Venti Gas leak. See Warning statement Optional Positioning of Thermostat Sensing Bulb Important Do not crimp capillaryWiring Diagram SpecificationsREMOTE-READY Models only Illustrated Parts Breakdown Illustrated Parts Breakdown Parts List THERMOSTAT-CONTROLLED Models2325 1026 Natural Gas Models Only REMOTE-READY Models Accessories Owners Registration Form Postage Required Replacement Parts Service HintsTechnical Service Parts Under WarrantyNot a UPC