Desa SL18NT Lighting Instructions, To Turn OFF GAS To Appliance, Thermostat Control Operation

Page 15

OPERATING HEATER

Continued

LIGHTING

INSTRUCTIONS

1.STOP! Read the safety information, page 14.

2.Make sure equipment shutoff valve is fully open.

3.Turn off any electric power to the appliance if service is to be performed.

4.Turn control knob clockwise to the OFF position.

5.Wait five minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information, page 14. If you donʼt smell gas, go to the next step.

6.Turn control knob counterclockwise to the PILOT position. Press in control knob for five (5) seconds.

7.With control knob pressed in, push down and release ignitor button. This will light pilot. The pilot is attached to the front of burner. Note: You may be running this heater for the first time after hooking up to gas supply. If so, you may need to press in control knob for 30 seconds or more. This will allow air to bleed from the gas system. If needed, keep pressing ignitor button until pilot lights. If ignitor does not light pilot, refer to Troubleshooting, page 18 or contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match.To light pilot with match, see Manual Lighting Procedure, page 16.

8.Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob.

•If control knob does not pop up when re- leased, contact a qualified service person or gas supplier for repairs.

Note: If pilot goes out, repeat steps 4 thru 7. Thermostat models have a safety interlock system. Wait one (1) minute before lighting pilot again.

9.Turn control knob counterclockwise to desired heating level. The main burner should light.

WARNING: Always operate manual control heaters at the locked positions. Operation between these positions may create a possible health hazard if used in a poorly ventilated room. Read owner’s manual for complete instructions.

CAUTION: Do not try to ad- just heating levels by using the equipment shutoff valve.

F

F

O

Figure 19 - Control Knob In The OFF

Position

Piezo Ignitor

Electronic Ignitor

 

Figure 20 - Ignitor Buttons

Thermocouple

Ignitor Electrode

Pilot Burner

Figure 21 - Pilot (actual pilot may vary)

 

TO TURN OFF GAS

 

 

TO APPLIANCE

 

Shutting Off Heater

 

1.

Turn control knob clockwise

to the

 

OFF position.

 

2.Turn off all electric power to the appliance if service is to be performed.

Shutting Off Burner Only (pilot stays lit)

Turn control knob clockwise

to the

PILOT position.

 

THERMOSTAT CONTROL

OPERATION

The thermostatic control used on these models differs from standard thermostats. Standard thermostats simply turn on and off the burner. The thermostat used on this heater senses the room temperature. The thermostat adjusts the amount of gas flow to the burner. This increases or decreases the burner flame height. At times the room may exceed the set temperature. If so, the burner will shut off. The burner will cycle back on when room temperature drops below the set temperature. The control knob can be set to any heat level between 1 and 5. Selecting the 5 setting will cause the burner to remain fully on without modulating down in most cases.

116292-01A

www.desatech.com

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents What to do if YOU Smell GAS Table of Contents Safety Information Unpacking Product FeaturesLocal Codes Product IdentificationUnusually Tight Construction AIR for Combustion VentilationProviding Adequate Ventilation Following are excerpts from National FuelDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationVentilation Air From Inside Building InstallationVentilation AIR Check GAS TypeInstallation Items Locating HeaterThis heater is designed to be mounted on a wall Installing Heater to Wall Placing Heater On Mounting Bracket Attaching Mounting Bracket To WallIs provided with heater For attaching mounting bracket to wall studsTor damage could occur Connecting to GAS SupplyInstalling Bottom Mounting Screws Important For natural gas, check gas lineChecking GAS Connections Min. Natural GasPropane/LP Gas Meter Equipment Test Pressures In Excess Of 1/2 Psig 3.5 kPaTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Equipment Open Shutoff Valve ClosedExtension Cord Connecting to Electrical SupplyFor Your Safety Read Before Lighting Operating HeaterShutting Off Heater Lighting InstructionsTo Turn OFF GAS To Appliance Thermostat Control OperationPilot Flame Pattern Manual Lighting ProcedureInspecting Heater Burner Flame PatternBurner Pilot AIR Inlet Cleaning MaintenancePilot Assembly Pilot Air Inlet ODS/PILOT and BurnerObserved Problem Possible Cause Remedy TroubleshootingODS/pilot lights but flame Goes out when control knob is Control knob not pressedDelayed ignition of burner Manifold pressure is too low Burner orifice is clogged Clean burner see CleaningAir passageways on heater Walls or furniture Cleaners, etc. may turn intoNo power to electric outlet 60Hz outlet Slight smoke or odor duringMent above Specifications Wiring DiagramsLSL18NT, SL18NT and VSL18NT LSL18PT, SL18PT and VSL18PT Service Publications Service Hints AccessoriesTechnical Service Replacement PartsModels LSL18NT, LSL18PT, SL18NT, SL18PT, VSL18NT and VSL18PT Illustrated Parts BreakdownParts List Parts Centrals 116292-01A Industrial Drive P.O. Box Patent Pending Warranty InformationKeep this Warranty Model Serial No Date of PurchaseQUÉ Hacer SI Percibe Olor a GAS Tabla DE Contenido Información DE Seguridad Características DEL Producto Información DECódigos Locales DesempaqueEspacio confinado y no confinado Aire Para Combustión VentilaciónCómo Proveer LA Ventilación Adecuada Construcción inusualmente selladaAire del interior de la construcción para ventilación Aire Para VentilaciónInstalación Verifique EL Tipo DE GASAire del exterior para ventilación Artículos DE Instalación Ubicación DEL CalentadorEste calentador está diseñado para montarse en una pared Panel de vidrio Separador Tornillo Instalación DEL Calentador EN LA ParedSoporte de montaje Desmontaje del panel anterior del calentadorDoble el anclaje de pared como se muestra en la figura Zando una broca de 9/64 de pulgadaCon los orificios que perforó en la pared En los maderos de la paredCalentador Pared Separador Conexión AL Suministro DE GASInstalación de los tornillos de montaje inferiores Quite el calentador del soporte de montajeCon rosca Cierre del Tipo NPT Tapón Equipo Unión T Unión terminal Buje reducTor a 1/8 De pulgada Válvula deTanque de suministro de propano o gas LP Válvula de Cierre de Equipo CerradaMedidor De gasPara SU SEGURIDAD, LEA Esto Antes DE Encenderlo Funcionamiento DEL CalentadorConexión a LA Alimentación Eléctrica Cable DE ExtensiónFuncionamiento DEL Instrucciones DE EncendidoApague el piloto Procedimiento DE Funcionamiento DELPatrón DE LA Llama DEL CalentadorGabinete Limpieza Y MantenimientoPiloto CON ODS Y Quemador Entrada DE Aire AL Piloto DEL QuemadorReemplace el regulador de gas Solución DE ProblemasProblema Observado Causa Posible Remedio La posición del regulador de gas no es la correctaCausa Posible Remedio Los conductos de aire en el El problema desapareceráHay aire en la línea de gas Hasta que se elimine el aire Línea de gasCia anterior LSL18PT, SL18PT y VSL18PT Diagramas DE CableadoEspecificaciones LSL18NT, SL18NT y VSL18NTPiezas DE Repuesto AccesoriosServicio Técnico Publicaciones DE ServicioModelos LSL18NT, LSL18PT, SL18NT, SL18PT, VSL18NT Y VSL18PT Clasificación Ilustrada DE PiezasLista DE Piezas Centrales DE Piezas Laporte’s Parts & Service 2444 N th StreetNotas Guarde Esta Garantía Información DE Garantía
Top Page Image Contents