Quadra-Fire 7008-115 owner manual Fireplace Size Requirements, Minimum Fireplace Opening

Page 15

5 Fireplace Size Requirements

A. Minimum Fireplace Opening

Minimum fireplace opening requirements are shown in Figure 5.1.

WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access.

Due to high temperatures, the appliance should be locat- ed out of traffic and away from furniture and draperies.

•The firebrick (refractory), glass doors, screen rails, screen mesh and log grates can be removed from a factory built firebox in order to gain minimum gas insert opening requirements.

•Any smoke shelves, shields and baffles may be removed from the factory built firebox if attached with mechanical fasteners.

•The metal floor of the solid fuel firebox may be removed to facilitate the installation of the insert. The appliance may not be placed directly on the base of the outer wrap, a 3/8 inch airspace must be provided between the insert and the floor of the outer wrap. Use the levelling legs to raise the insert a minimum of 3/8 inch. The original fireplace may never be returned to solid fuel in this condition. The sidewalls and top structure of the firebox may not be altered with the exception of removable baffles and dampers.

•Cutting of any sheet metal parts of the fireplace in which the gas fireplace insert is to be installed is prohibited, except the floor as tested for and as noted above.

RIGHT SIDE OF STOVE

A

C B

F

D

G

E

ROCKER SWITCH AND WIRING IS ACCESSIBLE HERE WHEN SHIPPED

H

ELECTRICAL CONNECTION AND GAS CONNECTION EXTEND

FROM HERE

 

 

 

A

B

 

C

 

D

E

 

F

 

G

H

 

 

inches

 

4-3/4

20

26-9/16

11-1/2

8-5/16

 

29

 

23

20

 

 

Millimeters

 

121

508

674

 

292

211

 

737

 

584

508

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MINIMUM FIREBOX OPENING

 

 

 

 

 

 

 

 

 

Height:

 

 

 

Width:

 

 

 

 

Depth:

 

 

 

 

 

Front

Rear

 

Front

 

 

Rear

Top

 

 

Bottom

 

Inches

20-1/4

14-1/2

 

26-1/2

 

 

20

 

13

 

 

 

13

 

 

Millimeters

514

368

 

673

 

 

508

 

330

 

 

330

 

Figure 5.1 Appliance Dimensions

Quadra-Fire • HUDBAY-INS • 7008-115 Rev. o • 8/11

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents What to do if you smell gas ModelHomeowner Reference Information CongratulationsUser Guide Table of ContentsLimited Lifetime Warranty Warranty Conditions Limited Lifetime WarrantyListing and Code Approvals Gas Fireplace Safety Operating Instructions User GuideYour Fireplace Decorative Doors, Fronts and Surrounds Fixed Glass AssemblyRemote Controls, Thermostats and Wall Switches Clear SpaceStanding Pilot Ignition For Your Safety Read Before LightingAfter Appliance is Lit Frequently Asked QuestionsMaintenance and Service Firebox Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection LogsTypical Appliance System Getting StartedDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Fireplace Size Requirements Minimum Fireplace OpeningMinimum fireplace opening requirements are shown in Figure Hearth Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Vent LimitsPlacing, Securing and Leveling the Appli- ance Damper Flashing Kit Optional Installing Adaptor and Termination CapMasonry Factory Built Wood BurningScrews Nuts Holding Burner PAN Gas InformationFuel Conversion Converting to LP GasValve Regulator Replacement Gas Connection Gas PressureElectrical Information Wiring RequirementsStanding Pilot Ignition System Wiring Wire Size Max. LengthBlower Installation Tools required Powered Phillips head screwdriverIncluded in kit Blower = 1/4 in mm female spade = 1/4 in mm male spade Clearance to Combustibles FinishingAppliance Setup Back of TOP Panel Screws Back of Side Panel Grille InstallationPanel Set Installation Tools required Philips head screwdriverPlacement of Embers Ember PlacementRetaining Tabs Brick InstallationRear Brick Retaining Tabs Positioning the LogsAir shutter is used to fine-tune the flame as necessary Air Shutter AdjustmentRemoving Fixed Glass Assembly Troubleshooting Symptom Possible Causes Corrective ActionStanding Pilot Ignition System Symptom Possible Cause Corrective Action TroubleshootingReference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits  B. Vent Kits ComponentsLog Set Assembly Service PartsPart number list on following Service Parts List StockedDepot Thermocouple 200-2950 Thermopile 842-0250 Description Comments Part NumberDo not Discard this Manual Contact Information

7008-115 specifications

The Quadra-Fire 7008-115 is a powerful and efficient wood stove that combines advanced technology with a classic design. It is ideal for homeowners looking to embrace a sustainable heating solution while enjoying the aesthetic appeal of a traditional wood-burning appliance. Known for its outstanding performance, this stove is a great addition to any living space.

One of the standout features of the Quadra-Fire 7008-115 is its exceptional heating capacity. This model is designed to heat large areas efficiently, making it suitable for both residential and commercial applications. With a heating output that can reach up to 800 square feet or more, it easily warms an entire room, providing comfort during cold winter months. Its large firebox can accommodate logs up to 18 inches in length, allowing for longer burn times and reduced refueling frequency.

The stove incorporates Quadra-Fire’s patented Technology, which enhances combustion efficiency and minimizes emissions. This advanced system ensures that the wood burns cleanly and completely, producing more heat and less smoke. The stove features an air-wash system that keeps the glass door clean, allowing users to enjoy a clear view of the flickering flames while maintaining air quality within the home.

In terms of design, the Quadra-Fire 7008-115 boasts a sleek and elegant appearance that blends seamlessly with various interior styles. Its cast iron construction provides durability and longevity, ensuring that the stove can withstand high temperatures without compromising structural integrity. Available in multiple finishes, including classic black and other decorative options, it complements any décor.

Safety is a priority with the Quadra-Fire 7008-115. It is equipped with a built-in safety barrier to prevent accidental contact with hot surfaces. Additionally, the stove adheres to strict EPA emissions standards, making it an eco-friendly choice for the environmentally conscious consumer.

Installation is made simple with the Quadra-Fire 7008-115, as it can be vented both vertically and horizontally, providing versatile options for installation in various home layouts. This adaptability ensures that homeowners can integrate the stove into their existing spaces without extensive renovations.

In conclusion, the Quadra-Fire 7008-115 is a top-tier wood stove that offers a blend of efficiency, safety, and classic design. With its advanced technologies and robust heating capabilities, it stands out as a reliable heating solution for those looking to enjoy the warmth and ambiance of a wood fire.
Top Page Image Contents