Quadra-Fire 7008-115 owner manual Appliance Setup

Page 29

12 Appliance Setup

A. Remove Glass Assembly

Uninstall the existing crown by removing the four screws

See Section 12.L.

on the back side of the door. Retain the screws.

 

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the firebox.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the firebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. Contact your dealer for a list of ap- proved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional acces- sories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

E. Door Crown Installation

Open lower access panel. Pull out and unhook the two spring latches on the bottom of the appliance that secure the door.

Rotate the door forward approximately 1-1/2 in. (38 mm). Holding the ashlip, lift the door up off of the stationary latches and away from the appliance.

Figure 12.2

Use a flat-head screwdriver to pry the black crown free on the right side. Remove the crown and discard.

STATIONARY LATCHES

SPRING LOADED LATCHES

Figure 12.1

Figure 12.3

Carefully align the left side of the crown into place, and wrap it across the face of door, finally snapping it into place on the right hand side. Reinsert and tighten the screws previously removed.

Figure 12.4

Note: Use a soft cloth and a window cleaning solution to clean all fingerprint oils from the gold or nickel surface of crown PRIOR to lighting the appliance.

Quadra-Fire • HUDBAY-INS • 7008-115 Rev. o • 8/11

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents What to do if you smell gas ModelHomeowner Reference Information CongratulationsUser Guide Table of ContentsLimited Lifetime Warranty Warranty Conditions Limited Lifetime WarrantyListing and Code Approvals Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Remote Controls, Thermostats and Wall Switches Fixed Glass AssemblyClear Space Decorative Doors, Fronts and SurroundsStanding Pilot Ignition For Your Safety Read Before LightingAfter Appliance is Lit Frequently Asked QuestionsMaintenance and Service Gasket Seal and Glass Assembly Inspection Maintenance Tasks-Service TechnicianLogs FireboxTypical Appliance System Getting StartedInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Minimum fireplace opening requirements are shown in Figure Fireplace Size RequirementsMinimum Fireplace Opening Hearth Mantel and Wall ProjectionsVent Termination Minimum Clearances Termination LocationsInstallation Preparation Connecting Vent Pipe Installing Vent Pipe and ApplianceVent Limits Venting ComponentsPlacing, Securing and Leveling the Appli- ance Masonry Installing Adaptor and Termination CapFactory Built Wood Burning Damper Flashing Kit OptionalFuel Conversion Gas InformationConverting to LP Gas Screws Nuts Holding Burner PANValve Regulator Replacement Gas Connection Gas PressureStanding Pilot Ignition System Wiring Wiring RequirementsWire Size Max. Length Electrical InformationIncluded in kit Blower Blower InstallationTools required Powered Phillips head screwdriver = 1/4 in mm female spade = 1/4 in mm male spade Clearance to Combustibles FinishingAppliance Setup Panel Set Installation Grille InstallationTools required Philips head screwdriver Back of TOP Panel Screws Back of Side PanelPlacement of Embers Ember PlacementRetaining Tabs Brick InstallationRear Brick Retaining Tabs Positioning the LogsAir shutter is used to fine-tune the flame as necessary Air Shutter AdjustmentRemoving Fixed Glass Assembly Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Symptom Possible Cause Corrective Action TroubleshootingReference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits  B. Vent Kits ComponentsPart number list on following Log Set AssemblyService Parts Depot Service Parts ListStocked Thermocouple 200-2950 Thermopile 842-0250 Description Comments Part NumberDo not Discard this Manual Contact Information

7008-115 specifications

The Quadra-Fire 7008-115 is a powerful and efficient wood stove that combines advanced technology with a classic design. It is ideal for homeowners looking to embrace a sustainable heating solution while enjoying the aesthetic appeal of a traditional wood-burning appliance. Known for its outstanding performance, this stove is a great addition to any living space.

One of the standout features of the Quadra-Fire 7008-115 is its exceptional heating capacity. This model is designed to heat large areas efficiently, making it suitable for both residential and commercial applications. With a heating output that can reach up to 800 square feet or more, it easily warms an entire room, providing comfort during cold winter months. Its large firebox can accommodate logs up to 18 inches in length, allowing for longer burn times and reduced refueling frequency.

The stove incorporates Quadra-Fire’s patented Technology, which enhances combustion efficiency and minimizes emissions. This advanced system ensures that the wood burns cleanly and completely, producing more heat and less smoke. The stove features an air-wash system that keeps the glass door clean, allowing users to enjoy a clear view of the flickering flames while maintaining air quality within the home.

In terms of design, the Quadra-Fire 7008-115 boasts a sleek and elegant appearance that blends seamlessly with various interior styles. Its cast iron construction provides durability and longevity, ensuring that the stove can withstand high temperatures without compromising structural integrity. Available in multiple finishes, including classic black and other decorative options, it complements any décor.

Safety is a priority with the Quadra-Fire 7008-115. It is equipped with a built-in safety barrier to prevent accidental contact with hot surfaces. Additionally, the stove adheres to strict EPA emissions standards, making it an eco-friendly choice for the environmentally conscious consumer.

Installation is made simple with the Quadra-Fire 7008-115, as it can be vented both vertically and horizontally, providing versatile options for installation in various home layouts. This adaptability ensures that homeowners can integrate the stove into their existing spaces without extensive renovations.

In conclusion, the Quadra-Fire 7008-115 is a top-tier wood stove that offers a blend of efficiency, safety, and classic design. With its advanced technologies and robust heating capabilities, it stands out as a reliable heating solution for those looking to enjoy the warmth and ambiance of a wood fire.
Top Page Image Contents