Quadra-Fire 7008-115 owner manual Blower Installation, Included in kit Blower

Page 26

C. Blower Installation

Included in kit: Blower.

Tools required: Powered Phillips head screwdriver.

Turn off gas and disconnect appliance from electricity. Remove logs and burner from appliance. Remove blower access cover in bottom of firebox by removing the screws. Retain screws for reassembly.

Disconnect wires from the blower.

Figure 10.2

Disconnect wires from the snap disk on back of access cover.

Figure 10.3

Lift blower off of studs and pull through opening.

Figure 10.4

Figure 10.5

Remove grommet retainer from old blower and install on new blower.

Figure 10.6 Installation is the reverse of removal.

26	Quadra-Fire • HUDBAY-INS • 7008-115 Rev. o • 8/11

Image 26

Contents Model What to do if you smell gasCongratulations Homeowner Reference InformationTable of Contents User GuideLimited Lifetime Warranty Limited Lifetime Warranty Warranty ConditionsListing and Code Approvals Your Fireplace Gas Fireplace SafetyOperating Instructions User Guide Clear Space Fixed Glass AssemblyRemote Controls, Thermostats and Wall Switches Decorative Doors, Fronts and SurroundsFor Your Safety Read Before Lighting Standing Pilot IgnitionFrequently Asked Questions After Appliance is LitMaintenance and Service Logs Maintenance Tasks-Service TechnicianGasket Seal and Glass Assembly Inspection FireboxGetting Started Typical Appliance SystemInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Minimum ﬁreplace opening requirements are shown in Figure Fireplace Size RequirementsMinimum Fireplace Opening Mantel and Wall Projections HearthTermination Locations Vent Termination Minimum ClearancesInstallation Preparation Vent Limits Installing Vent Pipe and ApplianceConnecting Vent Pipe Venting ComponentsPlacing, Securing and Leveling the Appli- ance Factory Built Wood Burning Installing Adaptor and Termination CapMasonry Damper Flashing Kit OptionalConverting to LP Gas Gas InformationFuel Conversion Screws Nuts Holding Burner PANValve Regulator Replacement Gas Pressure Gas ConnectionWire Size Max. Length Wiring RequirementsStanding Pilot Ignition System Wiring Electrical InformationIncluded in kit Blower Blower InstallationTools required Powered Phillips head screwdriver = 1/4 in mm female spade = 1/4 in mm male spade Finishing Clearance to CombustiblesAppliance Setup Tools required Philips head screwdriver Grille InstallationPanel Set Installation Back of TOP Panel Screws Back of Side PanelEmber Placement Placement of EmbersBrick Installation Retaining TabsPositioning the Logs Rear Brick Retaining TabsAir Shutter Adjustment Air shutter is used to fine-tune the flame as necessaryRemoving Fixed Glass Assembly Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Troubleshooting Symptom Possible Cause Corrective ActionAppliance Dimension Diagram Reference Materials B. Vent Kits Components Direct Vent Flex Liner KitsPart number list on following Log Set AssemblyService Parts Depot Service Parts ListStocked Description Comments Part Number Thermocouple 200-2950 Thermopile 842-0250Contact Information Do not Discard this Manual

7008-115 specifications

The Quadra-Fire 7008-115 is a powerful and efficient wood stove that combines advanced technology with a classic design. It is ideal for homeowners looking to embrace a sustainable heating solution while enjoying the aesthetic appeal of a traditional wood-burning appliance. Known for its outstanding performance, this stove is a great addition to any living space.

One of the standout features of the Quadra-Fire 7008-115 is its exceptional heating capacity. This model is designed to heat large areas efficiently, making it suitable for both residential and commercial applications. With a heating output that can reach up to 800 square feet or more, it easily warms an entire room, providing comfort during cold winter months. Its large firebox can accommodate logs up to 18 inches in length, allowing for longer burn times and reduced refueling frequency.

The stove incorporates Quadra-Fire’s patented Technology, which enhances combustion efficiency and minimizes emissions. This advanced system ensures that the wood burns cleanly and completely, producing more heat and less smoke. The stove features an air-wash system that keeps the glass door clean, allowing users to enjoy a clear view of the flickering flames while maintaining air quality within the home.

In terms of design, the Quadra-Fire 7008-115 boasts a sleek and elegant appearance that blends seamlessly with various interior styles. Its cast iron construction provides durability and longevity, ensuring that the stove can withstand high temperatures without compromising structural integrity. Available in multiple finishes, including classic black and other decorative options, it complements any décor.

Safety is a priority with the Quadra-Fire 7008-115. It is equipped with a built-in safety barrier to prevent accidental contact with hot surfaces. Additionally, the stove adheres to strict EPA emissions standards, making it an eco-friendly choice for the environmentally conscious consumer.

Installation is made simple with the Quadra-Fire 7008-115, as it can be vented both vertically and horizontally, providing versatile options for installation in various home layouts. This adaptability ensures that homeowners can integrate the stove into their existing spaces without extensive renovations.

In conclusion, the Quadra-Fire 7008-115 is a top-tier wood stove that offers a blend of efficiency, safety, and classic design. With its advanced technologies and robust heating capabilities, it stands out as a reliable heating solution for those looking to enjoy the warmth and ambiance of a wood fire.