Quadra-Fire QVI-30FB-S Electrical Information, Wiring the Appliance, Appliance Requirements

Page 17

9 Electrical Information

A. Wiring the Appliance

Appliance Requirements

Note: Electrical wiring must be installed by a licensed electrician.

Note: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric Code, CSA C221.1.

•A 110-120 VAC circuit for this product must be protected with ground-fault circuit-interrupter protection, in compliance with the applicable electrical codes, when it is installed in locations such as in bathrooms or near sinks.

•This appliance DOES NOT require 110-120 VAC to operate.

•It is recommended that a 110 VAC junction box be connected for use with fan or remote control. (See Figure 9.2 for junction box wiring).

WARNING

Wire 110V to electrical junction box.

Do NOT wire 110V to valve.

Do NOT wire 110V to wall switch.

•Incorrect wiring will damage millivolt valves.

•Incorrect wiring will override IPI safety lockout and may cause explosion.

CAUTION

•Prevent accidental appliance operation when not attended.

•Unplug or remove batteries from remote control if absent or if appliance will not be used for an extended period of time.

•Property damage possible from elevated temperatures.

ON/OFF Switch

•An ON/OFF switch is included with the decorative surround/decorative front and should attached to surround/facing. (See Installation instructions for remote control).

• If desired an additional wall switch or thermostat may be added to system as shown in Figure 9.1.

STANDING
PILOT
		REMOTE SWITCH
		PIGTAIL
		ON
		OFF
	VALVE	ON/OFF
	VALVE	SWITCH
		SWITCH
	WHT
	RED	OPTIONAL WALL SWITCH,
		THERMOSTAT OR REMOTE
Figure 9.1	Standing Pilot Ignition Wiring Diagram

Quadra-Fire • QVI-30FB-S • 2020-910 Rev. H • 6/09

17

Image 17

Contents Commonwealth of Massachusetts ModelsModel Number Serial Number Homeowner Reference InformationTable of Contents Listing and Code Approvals Getting Started Design and Installation ConsiderationsInspect Appliance and Components Tools and Supplies NeededInspect Firebox Minimum Fireplace Opening Fireplace Size RequirementsMinimum ﬁreplace opening requirements are shown in Figure LocationClearances to Mantels or other Combustibles above Appliance ClearancesVent Termination Minimum Clearances Termination LocationsFire Risk Asphyxiation Risk Foot minimum in snow regionsVent Table Key Vent Information and DiagramsHorizontal Venting Measuring StandardsInstallation Preparation Connecting Vent Pipe Installing Vent Pipe and ApplianceVenting Components Reference instructions in the termination kitPlacing, Securing and Leveling the Appliance Masonry Installing Adaptor and Termination CapFactory Built Wood Burning Damper Flashing Kit OptionalGas Information Refer to for location of gas line access in ap- plianceFuel Conversions Gas Connection Gas PressuresHigh Altitude Installations ON/OFF Switch Wiring the ApplianceElectrical Information Appliance RequirementsInstallation for Fan Optional Junction Box InstallationOptional Accessories Shock hazardFAN Junction BOX Mantel Projections Installing Trim SurroundsFinishing Clean the Appliance Appliance SetupAccessories Ember PlacementPositioning the Logs Log Assembly LOGS-QVI30FBLog Placement Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Air Shutter Setting Glass AssemblyRemoving Glass Assembly Replacing Glass AssemblyBefore Lighting Appliance Operating InstructionsThis appliance has a Standing Pilot Ignition Before operating this appliance have a qualified technicianStanding Pilot Ignition Lighting ApplianceCheck Pilot Flame Appearance Initial Break-in ProcedureAfter Appliance is Lit Do not operate appliance with glass door removedFrequently Asked Questions Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Maximum ﬂame impingement. Follow lighting instruc TroubleshootingSymptom Possible Cause Corrective Action Risk of injury or property damage Maintenance TasksMaintaining and Servicing Appliance Inspect Maintenance Tasks Reference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsService Parts Log Set AssemblyBeginning Manufacturing Date Oct Ending Manufacturing DateAt Depot Service Parts ListStocked Be ordered from an authorized dealer Valve AssemblyLimited Lifetime Warranty Limited Lifetime Warranty Important operating Contact Information