Quadra-Fire QVI-30FB-S owner manual Vent Kits Components, Direct Vent Flex Liner Kits

Page 35

B. Vent Kits Components

Direct Vent Flex Liner Kits (see Figure 15.2)

LINK-DV-30B or (LINK-DV-30): Masonry 3 inch ﬂex liner

kit. Expands to 30 feet. Includes: two liners, termination cap, ﬂashing, and link adapter.

LINK-DV4-30B or (LINK-DV4-30): Masonry 3 inch ﬂex liner kit. Expands to 30 feet and 4 feet respectively. Includes: two liners, termination cap, ﬂashing, and link adapter.

LINK-DV-30B (LINK-DV-30)

LINK-DV4-30B (LINK-DV4-30)

Figure 15.2 Direct Vent Flex Liner Kits

Direct Vent Flex Liner Accessory Kits (see Figure 15.3)

Flash-Damp: Zero clearance damper ﬂashing kit for use with LINK-DV-30B or LINK-DV4-30B liner kits.

LINK-ZC-ADP: Zero clearance chimney adapter

SVRLINK-ADP: Adapter kit (colinear to coaxial 3 inches included in above kits).

FLEX3-30: One 3 inch ﬂexible liner expands to 30 feet.

FLEX3-30/2: Two 3 inch ﬂexible liners expands to 30 feet each.

FLEX-CNCT: Connector kit - 3 inch liner to 3 inch liner, one connector per kit.

FLASH-DAMP

LINK-ZC-ADP

SVRLINK-ADP

FLEX3-30

FLEX3-30/2

FLEX3-CNCT

Figure 15.3 Direct Vent Flex Liner Accessory Kits

Quadra-Fire • QVI-30FB-S • 2020-910 Rev. H • 6/09

35

Image 35

Contents Commonwealth of Massachusetts ModelsModel Number Serial Number Homeowner Reference InformationTable of Contents Listing and Code Approvals Tools and Supplies Needed Design and Installation ConsiderationsGetting Started Inspect Appliance and ComponentsInspect Firebox Location Fireplace Size RequirementsMinimum Fireplace Opening Minimum ﬁreplace opening requirements are shown in FigureClearances to Mantels or other Combustibles above Appliance ClearancesFoot minimum in snow regions Termination LocationsVent Termination Minimum Clearances Fire Risk Asphyxiation RiskMeasuring Standards Vent Information and DiagramsVent Table Key Horizontal VentingInstallation Preparation Reference instructions in the termination kit Installing Vent Pipe and ApplianceConnecting Vent Pipe Venting ComponentsPlacing, Securing and Leveling the Appliance Damper Flashing Kit Optional Installing Adaptor and Termination CapMasonry Factory Built Wood BurningGas Pressures Refer to for location of gas line access in ap- plianceGas Information Fuel Conversions Gas ConnectionHigh Altitude Installations Appliance Requirements Wiring the ApplianceON/OFF Switch Electrical InformationShock hazard Junction Box InstallationInstallation for Fan Optional Optional AccessoriesFAN Junction BOX Mantel Projections Installing Trim SurroundsFinishing Ember Placement Appliance SetupClean the Appliance AccessoriesPositioning the Logs Log Assembly LOGS-QVI30FBLog Placement Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Replacing Glass Assembly Glass AssemblyAir Shutter Setting Removing Glass AssemblyBefore operating this appliance have a qualified technician Operating InstructionsBefore Lighting Appliance This appliance has a Standing Pilot IgnitionStanding Pilot Ignition Lighting ApplianceDo not operate appliance with glass door removed Initial Break-in ProcedureCheck Pilot Flame Appearance After Appliance is LitFrequently Asked Questions Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Maximum ﬂame impingement. Follow lighting instruc TroubleshootingSymptom Possible Cause Corrective Action Risk of injury or property damage Maintenance TasksMaintaining and Servicing Appliance Inspect Maintenance Tasks Reference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsEnding Manufacturing Date Log Set AssemblyService Parts Beginning Manufacturing Date OctAt Depot Service Parts ListStocked Be ordered from an authorized dealer Valve AssemblyLimited Lifetime Warranty Limited Lifetime Warranty Important operating Contact Information