Quadra-Fire QVI-30FB-S owner manual Operating Instructions, Before Lighting Appliance

Page 26

12 Operating Instructions

A. Before Lighting Appliance

This appliance has a Standing Pilot Ignition.

Before operating this appliance have a qualified technician:

•Remove all shipping materials from inside and/or underneath the firebox.

•Review proper placement of logs, rockwool, lava rock, and vermiculite.

•Check the wiring.

•Check the air shutter adjustment.

•Purge gas line (with glass assembly removed). See Section 8.

•Ensure that there are no gas leaks.

•Ensure that the glass is sealed and in the proper position.

•Ensure that the flow of combustion and ventilation air is not obstructed (front grilles and vent caps).

WARNING

Fire Risk.

Explosion Risk.

Gas may build up while lighting pilot.

•Remove glass assembly before lighting pilot.

•Replace glass assembly after lighting pilot.

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation AND cool down.

Hot glass will cause burns.

• DO NOT touch glass until it is cooled

•NEVER allow children to touch glass

•Keep children away

•CAREFULLY SUPERVISE children in same room as fireplace.

•Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable materials.

•Keep clothing, furniture, draperies and other flammable materials away.

This appliance has been supplied with an integral barrier to prevent direct contact with the fixed glass panel. DO NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or the gas supplier.

WARNING

Do NOT use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

26

Quadra-Fire • QVI-30FB-S • 2020-910 Rev. H • 6/09

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Models Commonwealth of MassachusettsHomeowner Reference Information Model Number Serial NumberTable of Contents Listing and Code Approvals Inspect Appliance and Components Design and Installation ConsiderationsGetting Started Tools and Supplies NeededInspect Firebox Minimum fireplace opening requirements are shown in Figure Fireplace Size RequirementsMinimum Fireplace Opening LocationClearances Clearances to Mantels or other Combustibles above ApplianceFire Risk Asphyxiation Risk Termination LocationsVent Termination Minimum Clearances Foot minimum in snow regionsHorizontal Venting Vent Information and DiagramsVent Table Key Measuring StandardsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Reference instructions in the termination kitPlacing, Securing and Leveling the Appliance Factory Built Wood Burning Installing Adaptor and Termination CapMasonry Damper Flashing Kit OptionalFuel Conversions Gas Connection Refer to for location of gas line access in ap- plianceGas Information Gas PressuresHigh Altitude Installations Electrical Information Wiring the ApplianceON/OFF Switch Appliance RequirementsOptional Accessories Junction Box InstallationInstallation for Fan Optional Shock hazardFAN Junction BOX Mantel Projections Installing Trim SurroundsFinishing Accessories Appliance SetupClean the Appliance Ember PlacementPositioning the Logs Log Assembly LOGS-QVI30FBLog Placement Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Removing Glass Assembly Glass AssemblyAir Shutter Setting Replacing Glass AssemblyThis appliance has a Standing Pilot Ignition Operating InstructionsBefore Lighting Appliance Before operating this appliance have a qualified technicianLighting Appliance Standing Pilot IgnitionAfter Appliance is Lit Initial Break-in ProcedureCheck Pilot Flame Appearance Do not operate appliance with glass door removedFrequently Asked Questions Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Maximum flame impingement. Follow lighting instruc TroubleshootingSymptom Possible Cause Corrective Action Risk of injury or property damage Maintenance TasksMaintaining and Servicing Appliance Inspect Maintenance Tasks Appliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsBeginning Manufacturing Date Oct Log Set AssemblyService Parts Ending Manufacturing DateAt Depot Service Parts ListStocked Valve Assembly Be ordered from an authorized dealerLimited Lifetime Warranty Limited Lifetime Warranty Contact Information Important operating
Top Page Image Contents