Quadra-Fire QVI-30FB-S Air Shutter Setting, Removing Glass Assembly, Replacing Glass Assembly

Page 25

F. Glass Assembly

WARNING

Handle glass doors with care.

•Inspect the gasket to ensure it is undamaged.

•Inspect the glass for cracks, chips or scratches.

•Do NOT strike, slam or scratch glass.

•Do NOT operate appliance with glass door removed, cracked, broken or scratched.

•Replace glass door assembly as a complete appliance.

Removing Glass Assembly

There are two glass latches on the bottom of glass assembly.

•To release glass assembly, pull latch forward and allow to retract away from glass assembly.

•Remove glass assembly after both latches have been released (see Figure 11.16).

Replacing Glass Assembly

Replace the glass door on the appliance. Fasten the latches on the glass frame.

FIREBOX

SURROUND

LOCATING TABS

Figure 11.16 Glass Assembly

G. Air Shutter Setting

Optimal ﬂame appearance is dependent on the air shutter setting. Adjustments should be made by a qualified technician.

	NG	LP
QVI-30FB-S	3/8 in.	Full open

Quadra-Fire • QVI-30FB-S • 2020-910 Rev. H • 6/09

25

Image 25

Contents Commonwealth of Massachusetts ModelsModel Number Serial Number Homeowner Reference InformationTable of Contents Listing and Code Approvals Getting Started Design and Installation ConsiderationsInspect Appliance and Components Tools and Supplies NeededInspect Firebox Minimum Fireplace Opening Fireplace Size RequirementsMinimum ﬁreplace opening requirements are shown in Figure LocationClearances to Mantels or other Combustibles above Appliance ClearancesVent Termination Minimum Clearances Termination LocationsFire Risk Asphyxiation Risk Foot minimum in snow regionsVent Table Key Vent Information and DiagramsHorizontal Venting Measuring StandardsInstallation Preparation Connecting Vent Pipe Installing Vent Pipe and ApplianceVenting Components Reference instructions in the termination kitPlacing, Securing and Leveling the Appliance Masonry Installing Adaptor and Termination CapFactory Built Wood Burning Damper Flashing Kit OptionalGas Information Refer to for location of gas line access in ap- plianceFuel Conversions Gas Connection Gas PressuresHigh Altitude Installations ON/OFF Switch Wiring the ApplianceElectrical Information Appliance RequirementsInstallation for Fan Optional Junction Box InstallationOptional Accessories Shock hazardFAN Junction BOX Finishing Installing Trim SurroundsMantel Projections Clean the Appliance Appliance SetupAccessories Ember PlacementLog Placement Log Assembly LOGS-QVI30FBPositioning the Logs Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Air Shutter Setting Glass AssemblyRemoving Glass Assembly Replacing Glass AssemblyBefore Lighting Appliance Operating InstructionsThis appliance has a Standing Pilot Ignition Before operating this appliance have a qualified technicianStanding Pilot Ignition Lighting ApplianceCheck Pilot Flame Appearance Initial Break-in ProcedureAfter Appliance is Lit Do not operate appliance with glass door removedFrequently Asked Questions Symptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Symptom Possible Cause Corrective Action TroubleshootingMaximum ﬂame impingement. Follow lighting instruc Maintaining and Servicing Appliance Maintenance TasksRisk of injury or property damage Inspect Maintenance Tasks Reference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsService Parts Log Set AssemblyBeginning Manufacturing Date Oct Ending Manufacturing DateStocked Service Parts ListAt Depot Be ordered from an authorized dealer Valve AssemblyLimited Lifetime Warranty Limited Lifetime Warranty Important operating Contact Information