Quadra-Fire QVI-30FB-S owner manual Finishing, Mantel Projections, Installing Trim Surrounds

Page 20

10 Finishing

A. Mantel Projections

Figure 10.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance, not the surround.

INLET AIR	12 in. MAX.
EXHAUST VENT PIPE
VENT PIPE
	MANTEL

12 in. MIN.

MEASUREMENTS FROM

TOP EDGE OF UNIT

Figure 10.1 Clearances to Mantels or other Combustibles above Appliance

B. Installing Trim Surrounds

Combustible materials MUST NEVER overlap onto the front face.

1.Find the coiled low voltage wires and ON/OFF switch at- tached to outer right side of the insert (see Figure 10.2).

2.Reconnect the low voltage wires to the ON/OFF switch.

3.Attach surround assembly by hooking the support bracket on the locating tabs on top of the gas insert ﬁreplace (see Figure 10.2.) Once the surround assem- bly is on the locating tabs, ensure the bottom hooks are resting on the locating pins at the base. Reposition the ﬁreplace if necessary. Refer to surround instruc- tions provided with the decorative surround.

	LOCATING TABS
	FIREBOX
	LOCATING SLOTS
Figure 10.2	Trim Surround Installation

20	Quadra-Fire • QVI-30FB-S • 2020-910 Rev. H • 6/09

Image 20

Contents Models Commonwealth of MassachusettsHomeowner Reference Information Model Number Serial NumberTable of Contents Listing and Code Approvals Design and Installation Considerations Getting StartedInspect Appliance and Components Tools and Supplies NeededInspect Firebox Fireplace Size Requirements Minimum Fireplace OpeningMinimum ﬁreplace opening requirements are shown in Figure LocationClearances Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesFire Risk Asphyxiation Risk Foot minimum in snow regionsVent Information and Diagrams Vent Table KeyHorizontal Venting Measuring StandardsInstallation Preparation Installing Vent Pipe and Appliance Connecting Vent PipeVenting Components Reference instructions in the termination kitPlacing, Securing and Leveling the Appliance Installing Adaptor and Termination Cap MasonryFactory Built Wood Burning Damper Flashing Kit OptionalRefer to for location of gas line access in ap- pliance Gas InformationFuel Conversions Gas Connection Gas PressuresHigh Altitude Installations Wiring the Appliance ON/OFF SwitchElectrical Information Appliance RequirementsJunction Box Installation Installation for Fan OptionalOptional Accessories Shock hazardFAN Junction BOX Mantel Projections Installing Trim SurroundsFinishing Appliance Setup Clean the ApplianceAccessories Ember PlacementPositioning the Logs Log Assembly LOGS-QVI30FBLog Placement Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Glass Assembly Air Shutter SettingRemoving Glass Assembly Replacing Glass AssemblyOperating Instructions Before Lighting ApplianceThis appliance has a Standing Pilot Ignition Before operating this appliance have a qualified technicianLighting Appliance Standing Pilot IgnitionInitial Break-in Procedure Check Pilot Flame AppearanceAfter Appliance is Lit Do not operate appliance with glass door removedFrequently Asked Questions Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Maximum ﬂame impingement. Follow lighting instruc TroubleshootingSymptom Possible Cause Corrective Action Risk of injury or property damage Maintenance TasksMaintaining and Servicing Appliance Inspect Maintenance Tasks Appliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsLog Set Assembly Service PartsBeginning Manufacturing Date Oct Ending Manufacturing DateAt Depot Service Parts ListStocked Valve Assembly Be ordered from an authorized dealerLimited Lifetime Warranty Limited Lifetime Warranty Contact Information Important operating