Quadra-Fire QVI-30FB-S owner manual Placing, Securing and Leveling the Appliance

Page 13

CUT AND BEND

FLASHING AS NEEDED

TO FIT CHIMNEY

SEALANT

ADHESIVE

Figure 7.2

•Trim chimney top plate to minimize excess overhang or bend over ﬂue tile (see Figure 7.2).

•Place 3/8 inch bead of 300º F silicone on ﬂue tile top.

C.Placing, Securing and Leveling the Appliance

•Install insert (without surround attached) into existing ﬁreplace while pulling collar slide plate forward.

•Install gas line into hole provided on insert side.

•If applicable install remote control wires into insert side (see Section 6, F.).

•Secure collar slide plate to appliance by placing locking handle into position with locking tabs (see Figure 7.1) and secure with #8 screw.

•Level the appliance from side to side and front to back. If necessary, use the leveling legs included with the insert to set each corner of the base.

•Position any excess ﬂexible vent pipe back up into chimney without sagging. Twist and push flex vent together to shorten.

•Install fiberglass insulation pieces to back face of surround.

•Attach surround. Follow instructions accompanying surround.

•Push insert so that surround becomes tight against face of ﬁreplace.

WARNING

Fire Risk.

Only an approved Hearth & Home Technologies surround may be used to cover integral grills on solid fuel burning ﬁreplaces.

• No other components such as shrouds, sheet- metal plates, etc., may be used to seal off vents.

WARNING

Failure to position the parts in accordance with these diagrams or failure to use only parts speciﬁcally approved with this appliance may result in property damage or personal injury.

WARNING

Explosion Risk.

Combustion Fume Risk.

•Connect vent sections per installation instructions.

•The 3 foot section of stainless steel ﬂexible pipe MUST be attached directly to the exhaust collar on the collar slide plate.

•Connect exhaust vent pipe ONLY to exhaust starting collar and termination cap center collar.

•Connect inlet air vent ONLY to inlet air collar on appliance and either the termination cap inlet air collar OR terminate within chimney.

•Do NOT allow vent to sag below connection point to appliance.

Quadra-Fire • QVI-30FB-S • 2020-910 Rev. H • 6/09

13

Image 13

Contents Commonwealth of Massachusetts ModelsModel Number Serial Number Homeowner Reference InformationTable of Contents Listing and Code Approvals Getting Started Design and Installation ConsiderationsInspect Appliance and Components Tools and Supplies NeededInspect Firebox Minimum Fireplace Opening Fireplace Size RequirementsMinimum ﬁreplace opening requirements are shown in Figure LocationClearances to Mantels or other Combustibles above Appliance ClearancesVent Termination Minimum Clearances Termination LocationsFire Risk Asphyxiation Risk Foot minimum in snow regionsVent Table Key Vent Information and DiagramsHorizontal Venting Measuring StandardsInstallation Preparation Connecting Vent Pipe Installing Vent Pipe and ApplianceVenting Components Reference instructions in the termination kitPlacing, Securing and Leveling the Appliance Masonry Installing Adaptor and Termination CapFactory Built Wood Burning Damper Flashing Kit OptionalGas Information Refer to for location of gas line access in ap- plianceFuel Conversions Gas Connection Gas PressuresHigh Altitude Installations ON/OFF Switch Wiring the ApplianceElectrical Information Appliance RequirementsInstallation for Fan Optional Junction Box InstallationOptional Accessories Shock hazardFAN Junction BOX Finishing Installing Trim SurroundsMantel Projections Clean the Appliance Appliance SetupAccessories Ember PlacementLog Placement Log Assembly LOGS-QVI30FBPositioning the Logs Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Air Shutter Setting Glass AssemblyRemoving Glass Assembly Replacing Glass AssemblyBefore Lighting Appliance Operating InstructionsThis appliance has a Standing Pilot Ignition Before operating this appliance have a qualified technicianStanding Pilot Ignition Lighting ApplianceCheck Pilot Flame Appearance Initial Break-in ProcedureAfter Appliance is Lit Do not operate appliance with glass door removedFrequently Asked Questions Symptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Symptom Possible Cause Corrective Action TroubleshootingMaximum ﬂame impingement. Follow lighting instruc Maintaining and Servicing Appliance Maintenance TasksRisk of injury or property damage Inspect Maintenance Tasks Reference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsService Parts Log Set AssemblyBeginning Manufacturing Date Oct Ending Manufacturing DateStocked Service Parts ListAt Depot Be ordered from an authorized dealer Valve AssemblyLimited Lifetime Warranty Limited Lifetime Warranty Important operating Contact Information