Quadra-Fire QVI-30FB-S owner manual Termination Locations, Vent Termination Minimum Clearances

Page 9

4 Termination Locations

A. Vent Termination Minimum Clearances

Figure 4.1 speciﬁes minimum vent heights for various pitched roofs.

HORIZONTAL

OVERHANG

WARNING

Fire Risk.

Asphyxiation Risk.

•Terminations MUST meet minimum clearances.

•Exhaust gases are hot.

•Nearby vents may draw fumes into house.

2FT.

MIN.

GAS DIRECT VENT

TERMINATION CAP

20 INCHES MIN.	VERTICAL
LOWEST	WALL
LOWEST
DISCHARGE
OPENING

ROOF PITCH

IS X/ 12

H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING

Roof Pitch	H (Min.) Ft.
Flat to 6/12	1.0*
Over 6/12 to 7/12	1.25*
Over 7/12 to 8/12	1.5*
Over 8/12 to 9/12	2.0*
Over 9/12 to 10/12	2.5*
Over 10/12 to 11/12	3.25
Over 11/12 to 12/12	4.0
Over 12/12 to 14/12	5.0
Over 14/12 to 16/12	6.0
Over 16/12 to 18/12	7.0
Over 18/12 to 20/12	7.5
Over 20/12 to 21/12	8.0

* 3 foot minimum in snow regions

Figure 4.1 Minimum height from roof to lowest discharge opening

Quadra-Fire • QVI-30FB-S • 2020-910 Rev. H • 6/09

Image 9

Contents Commonwealth of Massachusetts ModelsModel Number Serial Number Homeowner Reference InformationTable of Contents Listing and Code Approvals Getting Started Design and Installation ConsiderationsInspect Appliance and Components Tools and Supplies NeededInspect Firebox Minimum Fireplace Opening Fireplace Size RequirementsMinimum ﬁreplace opening requirements are shown in Figure LocationClearances to Mantels or other Combustibles above Appliance ClearancesVent Termination Minimum Clearances Termination LocationsFire Risk Asphyxiation Risk Foot minimum in snow regionsVent Table Key Vent Information and DiagramsHorizontal Venting Measuring StandardsInstallation Preparation Connecting Vent Pipe Installing Vent Pipe and ApplianceVenting Components Reference instructions in the termination kitPlacing, Securing and Leveling the Appliance Masonry Installing Adaptor and Termination CapFactory Built Wood Burning Damper Flashing Kit OptionalGas Information Refer to for location of gas line access in ap- plianceFuel Conversions Gas Connection Gas PressuresHigh Altitude Installations ON/OFF Switch Wiring the ApplianceElectrical Information Appliance RequirementsInstallation for Fan Optional Junction Box InstallationOptional Accessories Shock hazardFAN Junction BOX Installing Trim Surrounds FinishingMantel Projections Clean the Appliance Appliance SetupAccessories Ember PlacementLog Assembly LOGS-QVI30FB Log PlacementPositioning the Logs Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Air Shutter Setting Glass AssemblyRemoving Glass Assembly Replacing Glass AssemblyBefore Lighting Appliance Operating InstructionsThis appliance has a Standing Pilot Ignition Before operating this appliance have a qualified technicianStanding Pilot Ignition Lighting ApplianceCheck Pilot Flame Appearance Initial Break-in ProcedureAfter Appliance is Lit Do not operate appliance with glass door removedFrequently Asked Questions Troubleshooting Symptom Possible Causes Corrective ActionStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective ActionMaximum ﬂame impingement. Follow lighting instruc Maintenance Tasks Maintaining and Servicing ApplianceRisk of injury or property damage Inspect Maintenance Tasks Reference Materials Appliance Dimension DiagramDirect Vent Flex Liner Kits Vent Kits ComponentsService Parts Log Set AssemblyBeginning Manufacturing Date Oct Ending Manufacturing DateService Parts List StockedAt Depot Be ordered from an authorized dealer Valve AssemblyLimited Lifetime Warranty Limited Lifetime Warranty Important operating Contact Information