Quadra-Fire QVI-30FB-S owner manual Installing Adaptor and Termination Cap, Masonry

Page 14

D. Installing Adaptor and Termination Cap

For installation of termination cap see minimum vent heights for various pitched roofs (see Figure 7.3).

To install adaptor see Figure 7.4.

HORIZONTAL

OVERHANG

CAUTION

Sharp Edges

•Wear protective gloves and safety glasses during installation.

Damper Flashing Kit (Optional)

For use with LINK-DV4-30B Liner Kit.

2FT.

MIN.

GAS DIRECT VENT

TERMINATION CAP

20 INCHES MIN.	VERTICAL
LOWEST	WALL
LOWEST
DISCHARGE
OPENING

X

12

ROOF PITCH

IS X/ 12

H (MIN.) - MINIMUM HEIGHT FROM ROOF TO LOWEST DISCHARGE OPENING

Note: Damper may have to be removed to use this kit.

•Run ﬂex liners through 3” holes in damper ﬂashing.

•Attach damper ﬂashing to ﬁrebox roof with self tapping screws included in kit.

CLASS A PIPE

Roof Pitch	H (Min.) Ft.
Flat to 6/12	....................	1.0*
Over 6/12 to 7/12		1.25*
Over 7/12 to 8/12		1.5*
Over 8/12 to 9/12		2.0*
Over 9/12 to 10/12		2.5*
Over 10/12 to 11/12		3.25


Roof Pitch	H (Min.) Ft.
Over 11/12 to 12/12		4.0
Over 12/12 to 14/12		5.0
Over 14/12 to 16/12		6.0
Over 16/12 to 18/12		7.0
Over 18/12 to 20/12		7.5
Over 20/12 to 21/12		8.0

Figure 7.4

* 3 foot minimum in snow regions

Figure 7.3 Minimum Height from Roof to Lowest Discharge Opening

To help eliminate cold air drafts, it may be necessary to place non-combustible insulation around the ﬂues as they go though the damper.

Note: The LINK-DV4-30B system REQUIRES this insulation.

Masonry	LINK-DV30B	LINK-DV4-30B
	Installation	Installation
		TERMINATION
		CAP
EXHAUST		EXHAUST
AIR		AIR
VENT PIPE		VENT PIPE

ÍORÎ

WARNING:

DO NOT BLOCK

THIS PIPE END!

Note: Untwist the pipe while extending it, to achieve full 30’ length.

	INLET AIR	INLET AIR
		VENT PIPE
	VENT PIPE

Figure 7.5

Factory Built

Wood Burning

OPTIONAL LINK-ZC-ADPB

FOR USE WITH CLASS A

WOODBURNING PIPE

Remove 18 inch x 18 inch ﬂashing on cap by removing 3 screws. Connect both the LINK-ZC-ADPB to Class A Pipe and the termination cap to the LINK-ZC-ADPB with the self tapping screws provided.

14	Quadra-Fire • QVI-30FB-S • 2020-910 Rev. H • 6/09

Image 14

Contents Models Commonwealth of MassachusettsHomeowner Reference Information Model Number Serial NumberTable of Contents Listing and Code Approvals Inspect Appliance and Components Design and Installation ConsiderationsGetting Started Tools and Supplies NeededInspect Firebox Minimum ﬁreplace opening requirements are shown in Figure Fireplace Size RequirementsMinimum Fireplace Opening LocationClearances Clearances to Mantels or other Combustibles above ApplianceFire Risk Asphyxiation Risk Termination LocationsVent Termination Minimum Clearances Foot minimum in snow regionsHorizontal Venting Vent Information and DiagramsVent Table Key Measuring StandardsInstallation Preparation Venting Components Installing Vent Pipe and ApplianceConnecting Vent Pipe Reference instructions in the termination kitPlacing, Securing and Leveling the Appliance Factory Built Wood Burning Installing Adaptor and Termination CapMasonry Damper Flashing Kit OptionalFuel Conversions Gas Connection Refer to for location of gas line access in ap- plianceGas Information Gas PressuresHigh Altitude Installations Electrical Information Wiring the ApplianceON/OFF Switch Appliance RequirementsOptional Accessories Junction Box InstallationInstallation for Fan Optional Shock hazardFAN Junction BOX Mantel Projections Installing Trim SurroundsFinishing Accessories Appliance SetupClean the Appliance Ember PlacementPositioning the Logs Log Assembly LOGS-QVI30FBLog Placement Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Quadra-Fire QVI-30FB-S 2020-910 Rev. H 6/09 Removing Glass Assembly Glass AssemblyAir Shutter Setting Replacing Glass AssemblyThis appliance has a Standing Pilot Ignition Operating InstructionsBefore Lighting Appliance Before operating this appliance have a qualified technicianLighting Appliance Standing Pilot IgnitionAfter Appliance is Lit Initial Break-in ProcedureCheck Pilot Flame Appearance Do not operate appliance with glass door removedFrequently Asked Questions Standing Pilot Ignition System TroubleshootingSymptom Possible Causes Corrective Action Maximum ﬂame impingement. Follow lighting instruc TroubleshootingSymptom Possible Cause Corrective Action Risk of injury or property damage Maintenance TasksMaintaining and Servicing Appliance Inspect Maintenance Tasks Appliance Dimension Diagram Reference MaterialsVent Kits Components Direct Vent Flex Liner KitsBeginning Manufacturing Date Oct Log Set AssemblyService Parts Ending Manufacturing DateAt Depot Service Parts ListStocked Valve Assembly Be ordered from an authorized dealerLimited Lifetime Warranty Limited Lifetime Warranty Contact Information Important operating