(6)If you don’t want to make more ice, press
Ice Off | the Ice Off button. Pressing this button | |
(Hold 3 sec | 3 second locks the display panel and | |
for Child lock) | ||
dispenser buttons so the buttons can not | ||
| ||
| ||
| be used.The Child Lock icon lights up to | |
| indicate you’ve activated the Child Lock | |
| function. |
USING THE CONTROL PANEL
Basic temperature of Freezer and Refrigerator Compartments
The basic temperature and/or recommended temperature of Freezer and Refrigerator Compartments are
(7)
Cubed Ice
(8)
Crushed
Ice
(Cubed) (Crushed)
Press the Cubed Ice or Crushed Ice button to select the type of ice you want dispensed. Each time you press the button, the cubed and crushed ice modes alternate and the Cubed or Crushed ice icon lights up, indicating your selection.
If you don’t need ice, turn the function off to save on water and energy consumption (See Ice Off below).
If the temperature of Freezer and Refrigerator Compartments are too high or low, adjust the temperature manually.
Controlling the Freezer temperature
The Freezer temperature can be set between
the Freezer button repeatedly until the desired
( 9 ) |
| If you don’t want to make more ice, press | |||||
| the Ice Off button. |
| |||||
Ice Off |
| ||||||
The icon will light up and the | |||||||
|
|
| |||||
|
|
| stops making ice. |
| |||
|
|
| We recommend you stop ice making if the | ||||
|
|
| |||||
|
|
| following occur: |
| |||
|
|
| - There is enough ice in the ice bucket. | ||||
|
|
| - You want to save water and energy. | ||||
|
|
| - Water is not being supplied to the | ||||
|
|
| refrigerator. |
| |||
|
|
| If the ice maker function is ON, and | ||||
|
|
| the water line is not connected, | ||||
|
|
| there will be a | water valve noise | |||
|
|
| from back of the unit. Press the | ||||
|
|
| Ice Off(6) button until the Ice Off | ||||
|
|
| indicator ( |
|
| ) illuminates. | |
|
|
|
|
( 10 ) |
| Water filter usage | |
Filter | 1. | Normally the filter indicator is blue, | |
|
|
| yellow, or green when you purchase or |
|
|
| |
|
|
| install your refrigerator, depending on |
|
|
| your model. |
(Red) | 2. | After you use about 1020 L of water, | |
(Reset the |
|
| the filter indicator turns Light Pink. |
indicator) |
|
| (about 5 months) |
3.After you use about 1135 L of water, the filter indicator turns Red. (about
6 months) The icon will blink red for several seconds when you open or close the door.
4.Remove the old water filter and install a new one when the filter indicator is red. Reset the filter indicator by pressing Alam/Hold 3 sec for Filter Reset button for 3sec.
• If water is not dispensing or dispensing slowly, you need to replace the water filter because the water filter is clogged.
•Some areas have large amounts of lime in their water, which causes the water filter to clog more quickly.
14_ operating
temperature is shown in the temperature display. The temperature will move 1°C degrees with each press
Controlling the Refrigerator temperature
The Refrigerator temperature can be set between 7ºC and 1ºC to suit your particular needs. Press the Fridge button repeatedly until the desired temperature is shown in the temperature display.
The temperature will move 1°C degrees with each press (3°C → 2°C → 1°C → 7°C → 6°C → 5°C → 4°C
→3°C). The temperature control process for the Fridge works just like the Freezer process.
Press the Fridge button to set your desired temperature. After a few seconds, the Fridge will begin adjusting towards the newly set temperature. This will be refl ected in the digital display.
- The temperature of the Freezer, fridge or Convertible Room may rise when you open the doors too frequently, or if a large amount of warm or hot food is placed inside.
-This may cause the digital display to blink. Once the Freezer and fridge temperature return to their normal set temperatures, the blinking will stop.
-If the blinking continues, you may need to “reset” the Refrigerator. Try unplugging the appliance, wait for around 10 minutes and then plug the power cord back in.
-If there is an communication error between the Display and Main Controller, the Convertible Display light may blink. Once the normal set temperatures are reached, the blinking will stop. If the blinking continues for a long period of time, please contact a Samsung Electronics Service Center.
2015. 5. 7. 8:10 |