Vermont Casting SDDVT manual Venting Requirements and Options Direct Vent only

Page 13

Venting Requirements and Options -

Direct Vent ONLY

Approved Vent System Components

The Stardance Heater must be vented to the outdoors through an adjacent exterior wall or through the roof. The venting system must be comprised of the appropri- ate listed venting components specified on this page. These parts are available from DuraVent Corporation, Selkirk Corporation or your Vermont Castings Dealer.

See Figure 4 for dimensions relevant to the standard minimum-vent kits.

Simpson DuraVent Components

www.duravent.com

Phone: 1-800-835-4429, Fax: 1-707-446-4740

Minimum Horizontal Vent Kit

 

2792

Starter Pipe Assembly (incl. inner & outer sections)

2768*

90° Elbow, Blk.

46DVA-E90B*

45° Elbow, Gal.

46DVA-E45

6” Straight, Blk.

46DVA-06B*

9” Straight, Blk.

46DVA-09B

11” - 14⁵⁄” Adjustable Straight Section

46DVA-08AB

12” Straight

46DVA-12

24” Straight

46DVA-24B*

36” Straight

46DVA-36B

48” Straight

46DVA-48

Horizontal Vent Cap

46DVA-HC*

Wall Plate

46DVA-DC

Vinyl Siding Shield

46DVA-VSS

Snorkel Termination - 14”

46DVA-SNK14

Snorkel Termination - 36”

46DVA-SNK30

Wall Strap

46DVA-WS

Cathedral Ceiling Support Box

46DVA-CS

Storm Collar

46DVA-SC

Firestop Spacer

46DVA-FS

Flashing 0/12 - 6/12

46DVA-F6

Flashing 6/12 - 12/12

46DVA-F12

Steel Chimney Conversion Kit

 

 

Kit A (6⁵⁄” - 8⁵⁄”)

46DVA-KCA

Kit B (6⁵⁄” - 10¹⁄”)

46DVA-KCB

Kit C (6⁵⁄” - 13”)

46DVA-KCC

Masonry Chimney Conversion Kit

46DVA-KMC

Vertical Termination Cap (High Wind)

46DVA-VCH

Vertical Termination Cap (Low Profile)

46DVA-VC

*Included in Minimum Horizontal Vent Kit #2792

All DuraVent Straight vent pipe sections have a net length 1¹⁄” (37mm) less than the nominal dimension; i.e., a 6” (152mm) Straight pipe section has an effective length of 4¹⁄” (115mm).

Stardance Direct Vent/Natural Vent Gas Heater

Selkirk Corporation Vent Components

www.selkirkcorp.com

1301 W. President George Bush Highway Ste. 330 Richardson, TX 75080

Phone: 1-800-992-8368, Fax: 1-877-393-4145

Appliance Adapter

4DT-AAV

90° Elbow, Blk.

4DT-EL90B

45° Elbow, Blk.

4DT-EL45B

6” Straight, Blk.

4DT-06B

9” Straight, Blk.

4DT-09B

4” - 10” Adjustable Straight Section Blk.

4DT-AJ12B

12” Straight, Blk.

4DT-12B

18” Straight, Blk.

4DT-18B

24” Straight, Blk.

4DT-24B

36” Straight, Blk.

4DT-36B

48” Straight, Blk.

4DT-48B

Horizontal Termination

4DT-HC

Wall Thimble

4DT-WT

Vinyl Siding Standoff

4DT-VS

Snorkel Termination - 14”

4DT-ST14

Snorkel Termination - 36”

4DT-ST36

Wall Support Band

4DT-WS/B

Cathedral Ceiling Support Box

4DT-CCS

Storm Collar

4DT-SC

Firestop Spacer

4DT-FS

Flashing 0/12 - 6/12

4DT-AF6

Flashing 6/12 - 12/12

4DT-AF12

Steel Chimney

 

Horizontal Kit A

4DT-HKA

Horizontal Kit B

4DT-HKB

Vertical Kit

4DT-VKC

Masonry Chimney Kit

4DT-MCK

Vertical Termination Cap

4DT-VC

NOTE: Direct vent pipe may be used on the Natural Vent system from the top of the draft hood adapter to the ceiling.

20012734

13

Image 13
Contents Stardance Direct Vent/Natural Vent Gas Heater Table of Contents General Information Gas Equipment Venting System not Provided Installation RequirementsStardance dimensions Stardance Direct Vent / Natural Vent DimensionsMinimum Clearances to Combustible Clearance RequirementsMaterials Locating the StoveWall and Ceiling Clearances Wall Centerline from FloorHearth Requirements Direct Vent OnlyGas Inlet and Manifold Pressures Gas SpecificationsHigh Elevations Horizontal Termination Direct Vent onlyRestrictor Plate Adjustment Restrictor Plate Adjustment For Extended Pipe RunsRestrictor Plate is used on Direct Vent Installations Only Examples for Extended Run/Restrictor Plate SettingsLocation of Vent Termination Vent Termination ClearancesDirect Vent Only General Venting Information Termination Location Canadian Installations1 US Installations2Termination Clearances Venting Requirements Natural Vent OnlyApproved Vent System Components Venting Requirements and Options Direct Vent onlySimpson DuraVent Components Minimum Horizontal Vent Kit 2792CFM Vent Components Remove rear skirt insert Install the Optional FanVenting System Assemlby Direct Vent General Information Install the Vent Adapter PipeSide Wall Termination Assembly Install Vent Adapter PipeSelkirk Corporation Vent Components Assemble the wall sleeve and firestop Vent Termination Below Grade Vertical Through the Roof Vent AssemblySelkirk Direct-Temp Metalbestos Direct Vent System Horizontal Venting Vertical VentingInlet End Outlet End To Termination To ApplianceSupporting DIRECT-TEMP Vertical Support Adjustable Length AJOffsets Supporting DIRECT-TEMP Horizontal SupportBelow grade installation Vertical Installation Fig Minimum Height Above Roof Requirements Venting System Assembly Natural Vent General InformationInstall the Log Set Install the Vent PipeStardance Direct Vent/Natural Vent Gas Heater Connect the Gas Supply Line Install ON/OFF SwitchBurner Information Operation Install the Front PlateThermostat Connection optional Your First FireFlame Characteristics Flame & Temperature AdjustmentSddvt Series Sddvtc Series Comfort Control ModelsTo Turn Off Gas To Heater Lighting and Operating InstructionsEuro SIT HoneywellSIT Nova 820 Millivolt Valve Troubleshooting the Gas Control System Sddvt SeriesTransmitter Operation Off Mode Shut Off ProcedureOn Manual Mode Delay Timer ModeFan Override During Auto Mode Auto ModeChange Between F/C Temperature Units Disable Thermostat FunctionOn Path Local PathAuto Path Conversion Procedure Conversion PrecautionsFuel Conversion Instructions Valve Conversion Sddvt Series ModelsPilot Type Pilot Orifice ConversionValve All Models Burner Orifice ConversionBottom View Conversion to LP Input BTU/h Injector Orifice Size MatrixConversion to Natural Gas Input BTU/h Logset and Burner Cleaning and Inspection MaintenanceCleaning the Glass Glass ReplacementStove Disassembly Gasket ReplacementInspect the Vent System Annually Check the Gas Flame RegularlyOn/Off Switch Wiring Wiring DiagramsOptional Thermostat Wiring Schematic DiagramStardance Direct Vent/Natural Vent Gas Heater Description Stardance Direct Vent/Natural Vent Gas HeaterFuel Conversion Kits Optional Accessories Stardance Direct Vent/Natural Vent Gas Heater Stardance Direct Vent/Natural Vent Gas Heater Stardance Direct Vent/Natural Vent Gas Heater Limited Lifetime Warranty CFM Corporation

SDDVT specifications

Vermont Casting's SDDVT, or the Signature Series Direct Vent Technology, represents a remarkable blend of design, efficiency, and functionality in the world of high-performance heating appliances. Known for its commitment to craftsmanship, Vermont Casting has long been synonymous with quality, and the SDDVT is no exception.

One of the standout features of the SDDVT is its advanced direct venting capability. This system allows for efficient venting of combustion gases directly outside, minimizing the risk of backdrafting and ensuring optimal indoor air quality. It draws air from the outside for combustion, creating a more controlled environment that enhances both efficiency and safety. Homeowners can rest easy knowing that the SDDVT provides a reliable heating solution while protecting indoor air quality.

Another significant aspect of the SDDVT is its high-efficiency performance. With an impressive Annual Fuel Utilization Efficiency (AFUE) rating, the SDDVT maximizes heat output while minimizing fuel consumption. This efficiency translates to lower energy bills and a reduced carbon footprint, making it an environmentally friendly choice for heating. The unit is designed to operate effectively even in extremely cold temperatures, ensuring comfort throughout the winter months.

The SDDVT also boasts an array of customizable options that appeal to a wide range of aesthetic preferences. Available in various finishes and styles, including traditional cast iron and sleek modern designs, homeowners can select a model that complements their decor. The unit features a large viewing glass that provides an unobstructed view of the flames, creating a cozy ambiance that enhances the living space.

Incorporating cutting-edge technology, the SDDVT includes electronic ignition and advanced control systems, allowing users to easily manage their heating preferences. The integration of smart technology enables compatibility with home automation systems, giving users added convenience and control.

Overall, Vermont Casting's SDDVT is an exemplary heating solution characterized by its innovative direct venting technology, high efficiency, and customizable design options. With a focus on quality and performance, this unit exemplifies the brand's dedication to providing sustainable and effective heating solutions tailored to modern living. Whether for new construction or retrofitting existing spaces, the SDDVT stands as a premier choice for comfort and style.