Vermont Casting SDDVT manual Vertical Installation Fig

Page 24

Stardance Direct Vent/Natural Vent Gas Heater

Horizontal Termination

ST931

Fig. 41 Horizontal termination.

Vinyl Siding Standoff

Horizontal Termination

ST932

Fig. 42 Vinyl siding standoff and horizontal termination.

7.If a wall thimble is used, push the pipe (which is connected to the appliance) carefully through the wall thimble until the DIRECT-TEMP pipe becomes fully engaged with the horizontal termination. If no thimble is used, place the Trim Plate (TP) on the DIRECT-TEMP pipe. Carefully push the DIRECT-TEMP pipe through the wall until fully engaged with the horizontal termina- tion. Secure the trim plate to the wall.

NOTE: If a vertical rise is necessary on the exterior side of the building, a 14” (356 mm) and 36” (914 mm) Snor- kel Termination (ST) is available. Follow the installation procedures for horizontal terminations. If the snorkel termination is to be located below grade, a window well is recommended with adequate and proper drainage as per local codes. Leave 2” (51 mm) clearance be- low snorkel to prevent water from entering the snorkel termination. Do not enclose the snorkel within a wall or other type of enclosure and do not back fill. Ensure that grade level slopes away from the building. (Fig. 39)

Vertical Installation (Fig. 43)

1.Determine the location of the appliance. Choose a location which provides adequate clearance from obstacles such as electrical wiring, conduit, framing members, plumbing pipe, etc.

Vertical Termination

Storm Collar

Approved Silicone

Sealant Here

Flashing

Offset Support

Collar

Firestop

Spacer

Ceiling

 

 

Support

Ceiling Support Collar

 

Plate

 

 

 

 

Trim Plate

ST933

 

 

Fig. 43 Typical vertical venting configuration.

2.After positioning the appliance, determine where the vent pipe will pass through the ceiling. This can be done by using a plum bob or a small weight attached to a string. Hold the plum bob from the ceiling moving it until it lines up with the centerline of the outlet of the appli- ance. Mark the position on the ceiling.

NOTE: Frame openings to the dimensions specified in the framing table for the cathedral ceiling support box (CCS), the ceiling support (SC) and wherever the firestop spacer (FS) is being used.

3.Cut and frame the appropriate sized square hole through the ceiling. Repeat the process for other ceiling penetrations as necessary.

4.Determine and mark the roof penetration in the same manner.

5.Cut a hole in the roof at this point large enough to satisfy all clearance-to-combustible requirements as specified by the appliance manufacturer’s installation instructions.

24

20012734

Image 24
Contents Stardance Direct Vent/Natural Vent Gas Heater Table of Contents General Information Installation Requirements Gas Equipment Venting System not ProvidedStardance Direct Vent / Natural Vent Dimensions Stardance dimensionsClearance Requirements Minimum Clearances to CombustibleMaterials Locating the StoveWall Centerline from Floor Wall and Ceiling ClearancesHearth Requirements Direct Vent OnlyGas Specifications Gas Inlet and Manifold PressuresHigh Elevations Horizontal Termination Direct Vent onlyRestrictor Plate Adjustment For Extended Pipe Runs Restrictor Plate AdjustmentRestrictor Plate is used on Direct Vent Installations Only Examples for Extended Run/Restrictor Plate SettingsVent Termination Clearances Location of Vent TerminationDirect Vent Only Canadian Installations1 US Installations2 General Venting Information Termination LocationVenting Requirements Natural Vent Only Termination ClearancesVenting Requirements and Options Direct Vent only Approved Vent System ComponentsSimpson DuraVent Components Minimum Horizontal Vent Kit 2792CFM Vent Components Install the Optional Fan Remove rear skirt insertInstall the Vent Adapter Pipe Venting System Assemlby Direct Vent General InformationInstall Vent Adapter Pipe Side Wall Termination AssemblySelkirk Corporation Vent Components Assemble the wall sleeve and firestop Vertical Through the Roof Vent Assembly Vent Termination Below GradeSelkirk Direct-Temp Metalbestos Direct Vent System Vertical Venting Horizontal VentingInlet End Outlet End To Termination To ApplianceAdjustable Length AJ Supporting DIRECT-TEMP Vertical SupportOffsets Supporting DIRECT-TEMP Horizontal SupportBelow grade installation Vertical Installation Fig Venting System Assembly Natural Vent General Information Minimum Height Above Roof RequirementsInstall the Vent Pipe Install the Log SetStardance Direct Vent/Natural Vent Gas Heater Install ON/OFF Switch Connect the Gas Supply LineBurner Information Install the Front Plate OperationThermostat Connection optional Your First FireFlame & Temperature Adjustment Flame CharacteristicsSddvt Series Sddvtc Series Comfort Control ModelsLighting and Operating Instructions To Turn Off Gas To HeaterEuro SIT HoneywellTroubleshooting the Gas Control System Sddvt Series SIT Nova 820 Millivolt ValveShut Off Procedure Transmitter Operation Off ModeOn Manual Mode Delay Timer ModeAuto Mode Fan Override During Auto ModeChange Between F/C Temperature Units Disable Thermostat FunctionLocal Path On PathAuto Path Conversion Precautions Conversion ProcedureFuel Conversion Instructions Valve Conversion Sddvt Series ModelsPilot Orifice Conversion Pilot TypeValve Burner Orifice Conversion All ModelsBottom View Injector Orifice Size Matrix Conversion to LP Input BTU/hConversion to Natural Gas Input BTU/h Maintenance Logset and Burner Cleaning and InspectionCleaning the Glass Glass ReplacementGasket Replacement Stove DisassemblyInspect the Vent System Annually Check the Gas Flame RegularlyWiring Diagrams On/Off Switch WiringOptional Thermostat Wiring Schematic DiagramStardance Direct Vent/Natural Vent Gas Heater Stardance Direct Vent/Natural Vent Gas Heater DescriptionFuel Conversion Kits Optional Accessories Stardance Direct Vent/Natural Vent Gas Heater Stardance Direct Vent/Natural Vent Gas Heater Stardance Direct Vent/Natural Vent Gas Heater Limited Lifetime Warranty CFM Corporation

SDDVT specifications

Vermont Casting's SDDVT, or the Signature Series Direct Vent Technology, represents a remarkable blend of design, efficiency, and functionality in the world of high-performance heating appliances. Known for its commitment to craftsmanship, Vermont Casting has long been synonymous with quality, and the SDDVT is no exception.

One of the standout features of the SDDVT is its advanced direct venting capability. This system allows for efficient venting of combustion gases directly outside, minimizing the risk of backdrafting and ensuring optimal indoor air quality. It draws air from the outside for combustion, creating a more controlled environment that enhances both efficiency and safety. Homeowners can rest easy knowing that the SDDVT provides a reliable heating solution while protecting indoor air quality.

Another significant aspect of the SDDVT is its high-efficiency performance. With an impressive Annual Fuel Utilization Efficiency (AFUE) rating, the SDDVT maximizes heat output while minimizing fuel consumption. This efficiency translates to lower energy bills and a reduced carbon footprint, making it an environmentally friendly choice for heating. The unit is designed to operate effectively even in extremely cold temperatures, ensuring comfort throughout the winter months.

The SDDVT also boasts an array of customizable options that appeal to a wide range of aesthetic preferences. Available in various finishes and styles, including traditional cast iron and sleek modern designs, homeowners can select a model that complements their decor. The unit features a large viewing glass that provides an unobstructed view of the flames, creating a cozy ambiance that enhances the living space.

Incorporating cutting-edge technology, the SDDVT includes electronic ignition and advanced control systems, allowing users to easily manage their heating preferences. The integration of smart technology enables compatibility with home automation systems, giving users added convenience and control.

Overall, Vermont Casting's SDDVT is an exemplary heating solution characterized by its innovative direct venting technology, high efficiency, and customizable design options. With a focus on quality and performance, this unit exemplifies the brand's dedication to providing sustainable and effective heating solutions tailored to modern living. Whether for new construction or retrofitting existing spaces, the SDDVT stands as a premier choice for comfort and style.