Honeywell LYNXR-2 manual General Operation

Page 7

SYSTEM OVERVIEW

General Operation

Zones

Your system's sensing devices have been assigned to various "zones." For example, the sensing device on your entry/exit door may have been assigned to zone 01, sensing devices on windows in the master bedroom to zone 02, and so on. These numbers appear on the display when an alarm or trouble condition occurs.

Fire Protection

The fire protection portion of your security system (if used) is always active and will sound an alarm if a fire condition is detected. Refer to the FIRE ALARM SYSTEM section for important information concerning fire protection, smoke detectors and planning emergency exit routes from the premises.

UL

LYNXR-2 Series is not intended for UL985 Household Fire applications unless a 24-hour backup

battery (P/N LYNXRCHKIT-HC) is installed.

 

 

Burglary Protection

Your system provides two modes of burglary protection: STAY and AWAY. STAY mode protects the perimeter only, allowing you to freely move inside the premises. AWAY mode protects the entire system. Both modes provide an entry delay time that allows you to reenter the premises without setting off an alarm. For additional security, you can turn the entry delay off when arming the system by using

the

NO DELAY

key in combination with the desired arming key. The system also allows you to bypass

selected zones before arming the system, if desired. Refer to the BYPASSING PROTECTION ZONES section. The system also provides a CHIME mode, for alerting users to the opening of protected doors and windows while the system is disarmed.

You must turn on ("arm") the burglary protection portion of your system before it will sense burglary alarms. To arm the system, enter your user code then press the desired arming key (AWAY or STAY). Refer to the ARMING THE SYSTEM section for detailed procedures and information.

Security Codes

At the time of installation, you were assigned a personal 4-digit security or “master user” code. You must enter the user code when arming and disarming the system, and when performing other system functions. As an additional security feature, other users who do not need to know your code can be assigned up to 6 different security codes. Refer to the SECURITY CODES section for procedures on adding security codes to the system.

Alarms

When an alarm occurs, the keypad and external sounders will sound for about 15-seconds, and the keypad will display the zone(s) causing the alarm. After 15-seconds, the siren stops temporarily and voice announcements of the zones in alarm begins. When these zones have been announced, the siren sounds again and the cycle repeats itself, until the system is disarmed (CODE + OFF) or until alarm bell timeout occurs. If your system is connected to a central monitoring station, an alarm message will be sent. To stop the alarm sounding, simply disarm the system. The zone(s) causing the alarm remain displayed indicating memory of alarm. Refer to the DISARMING THE SYSTEM section for information about clearing the memory of alarm display

– 7 –

Page 6 Page 8
Image 7
Page 6 Page 8
Contents LYNXR-2 Series Security System Page Table of Contents Page System Overview FeaturesLYNXR-2SIA False Alarm Prevention Features General Operation Two-Way Voice Feature Quick View of System Functions To remotely activate X10 devices 07 To turn Test mode onTo turn Test mode off To remotely activate X10 devicesGeneral About the Master Keypad2ARMED 3READY Master Keypad DefinitionsLights on / Lights OFF Keys Turns LED Meanings About the Display and IndicatorsChecking System Status Securing the PremisesExit Delay Restart/Reset Arming in Stay ModeArming In Away Mode Restarting Exit Delay While System ArmedQuick Arming Auto Stay FeatureArming the System with No Delay To arm with no Delay if Quick Arm is activeLYNXR-2SIA Exit/Entry Delay Times Entry/Exit DelaysExit Delay Entry DelayTo disarm the system and silence burglary alarms Memory of AlarmDisarming the System Displaying Bypassed Zones Bypassing Protection ZonesBypassing Individual Zones Forced BypassChime Mode Panic Keys / Chime ModePanic Keys Code Format Paging FeatureUser Functions Automatic PagingReminder Announcements Follow Me Announcement FeatureFollow Me Reminder and System Announcements System AnnouncementsTo delete Follow Me reminder telephone number To program Follow Me reminder telephone numberTo deactivate X10 devices 07 Device DescriptionsDeleting Messages Message Recording/Playback/Volume ControlRecording a Message Message PlaybackTo adjust message playback/system announcement volume Adjusting the VolumeTo restore announcement sounding Function + Defining the AUX Function AUX FunctionPerforming the AUX function Month Clock/CalendarHour MinuteYear DayScheduling User Interface Schedule number = the value that was last stored in the memoryEnd Time minute Entry Event Comment Event Identifier EntriesEntry Day Day of Week EntriesUsing Remote Phone Control Feature Remote Phone Control FeatureEnter To remotely arm in Away mode Remote Phone Control Commands To remotely disarm systemTo remotely Bypass zones Using the Speaker Phone Feature Speaker Phone FeatureEntering # + Remote Services General Information Silencing a Fire AlarmCase of Fire Living Room Bedroom Fire Alarm SystemEmergency Evacuation Security Codes System FunctionsTo Add/Delete a User or Change a Users Code Entering Test Mode Testing the System to be conducted weeklyExit Test Mode Typical Trouble Condition Displays Trouble MessagesRoutine Care Changing the LYNXR-2 Series System Battery Low Battery Conditions in Wireless SensorsMaintaining your system Sound Cause Display Announcement Summary of Audible NotificationAdditional Announcements Industry Canada Federal Communications Commission FCC Part 15 StatementRinger Equivalence Number Notice Federal Communications Commission FCC PartEvent of Telephone Operational Problems Servicing Information Page Notifies Insert B = Burglary, F = Fire Owners Insurance Premium Credit RequestOwners Insurance Premium Credit Request Limitations of this Alarm System Page Page Page Index No delay Pager ONE Year Limited Warranty ÊK15012yŠ

LYNXR-2 specifications

The Honeywell LYNXR-2 is an advanced wireless security system designed for residential and light commercial applications. Recognized for its user-friendly interface, the LYNXR-2 combines cutting-edge technology with essential security features, making it a popular choice among homeowners seeking peace of mind.

One of the primary characteristics of the LYNXR-2 is its sleek, modern design, which includes a large, easy-to-read touchscreen display. This intuitive interface allows users to manage their security system with minimal effort. From arming and disarming the system to viewing alerts, the touchscreen simplifies the interaction for users of all ages.

The LYNXR-2 employs Honeywell’s innovative technology, which integrates both security and home automation functionalities. This powerful system supports a wide range of wireless sensors, including door/window contacts, motion detectors, and smoke detectors. The flexibility of wireless technology means users can easily expand their security coverage without the need for complicated wiring.

Another notable feature of the LYNXR-2 is its built-in Z-Wave technology. This allows for seamless integration with smart home devices, enabling users to control lights, locks, and thermostats through the same interface. Home automation capabilities enhance security further by allowing users to program their system to perform specific actions, such as turning on lights when entering a home.

The LYNXR-2 system also offers robust communication features. It comes equipped with a cellular backup, ensuring that users remain connected to monitoring services even during power outages or if the phone line is cut. Additionally, the system supports both IP and cellular connectivity, providing flexibility in how users choose to connect their systems to monitoring services.

For those looking for added functionality, the LYNXR-2 can be easily integrated with Honeywell’s Total Connect Remote Services. This allows users to monitor and control their security system remotely through a smartphone or tablet, providing real-time notifications and updates on system status.

In summary, the Honeywell LYNXR-2 stands out for its combination of user-friendly features, advanced technologies, and extensive security and automation capabilities. It is an ideal solution for individuals seeking a reliable, scalable, and easy-to-use security system for their homes or light commercial properties. With its comprehensive features and seamless integration, the LYNXR-2 is poised to meet the security needs of modern living.
Top Page Image Contents