New Buck Corporation MODEL FP-327-ZC Thermostat Control Operation, Manual Lighting Procedure

Page 26

THERMOSTAT CONTROL OPERATION

THERMOSTAT CONTROL OPERATION

•This valve operates off of millivolts produced by the generator. You may choose to use an optional Wall Thermostat or Remote control. If so, see Figure 2, page 22 for wiring diagram.

MANUAL LIGHTING PROCEDURE

1.If the pilot cannot be lit with the piezo, it can be manually lit with the use of a paper match and a lighter rod.

2.Open access panel door located at bottom front of the appliance.

3.2. Place the match in the holder and light. With the left hand, turn the control knob

counterclockwise	to “PILOT”position. Press in gas control knob for fifteen (15)
seconds.

4.Use rod to light match and ignite pilot. The pilot is located in front of the rear log and burner on the right hand side of the appliance.

5.Continue to hold the control knob for an additional one (1) minute to ensure the pilot is lit.

6.	Turn control knob counterclockwise	to the “ON” position. Push the “ON/
	OFF” toggle switch to the “ON” position. The main burner should light.

7.Close access panel door.

8.Turn on all electrical power to the appliance.

NOTE: This unit may be used with an optional Wall Thermostat. If so, the Wall Thermostat needs to be set at a higher temperature than the room temperature.

Page 24

Image 26

Contents Manufacturer NEW BUCK CORPORATION P.O. Box MODEL FP-327-ZCNEW BUCK CORPORATION 8000 Highway 226 South Spruce Pine, NCPage TABLE OF CONTENTS Page SECTION I SAFETY INFORMATION WARNINGS Page Page GAS LINE SECTION ZERO CLEARANCE INSTALLATIONCHOOSING THE LOCATION FOR YOUR FIREPLACE DRAFTS7 1/2 Fireplace and Framing Dimensions inches3 1/4 PageInstall the Firebox INSTALLING THE FIREBOXFIREPLACE CLEARANCES Framing the FireboxFINISHING YOUR FIREPLACE CLEARANCESMANTEL 3/4 FLAT SURFACE MANTEL PROFILES FOR ZERO CLEARANCE CABINETMUST BE FOLLOWED MANTEL 3/4 FLAT SURFACEINSTALLATION OF MODEL FP - 327- ZC WITH OPTIONAL WOODEN MANTELREAR OF HEATER 1/2 WOOD SCREWSTOP MANTEL MANTEL BASESECTION AFTER MARKET MOBILE HOME INSTALLATION PRODUCING ADEQUATE VENTILATION DETERMINING FRESH-AIRFLOW FOR HEATER LOCATIONVent-freeheater VENTILATION AIR VENTILATION AIR FROM INSIDE BUILDINGVENTILATION AIR FROM OUTDOORS GAS CONNECTION FLAMEGAS PRESSURE CHECK PLACEMENT OF LOGSSEE DIAGRAM ON PAGE Page PLACEMENT OF LOGS3 1 2 Figure WHAT TO DO IF YOU SMELL GAS FOR YOUR SAFETY, READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS MILLIVOLT VALVE ITT REMOVE METAL CONNECTOR ROCKER SWITCHBEFORE INSTALLING THERMOSTAT PageTHERMO--COUPLEPILE IGNITOR ELECTRODEPILOT BURNER PageMANUAL LIGHTING PROCEDURE THERMOSTAT CONTROL OPERATIONLIGHTING INSTRUCTIONS MODULATING VALVEMAXITROL FOR YOUR SAFETY, READ BEFORE LIGHTINGfor “LOW” LIGHTING INSTRUCTIONSto IGNITE and for “HIGH”TO TURN OFF GAS TO APPLIANCE IGNITER ELECTRODE THERMO-COUPLEO.D.S PILOT BURNER MANUAL LIGHTING PROCEDURE THERMOSTAT CONTROL OPERATIONBURNER FLAME CHECKNATURAL PILOT PROPANE PILOTWIRING DIAGRAM Page NOTE #PESBRO84 Blower Model FP-327-ZCRating 120 volts/60HZ/0.54 Amps IMPORTANT SAFEGUARDS CLEANINGTROUBLE SHOOTING Air in gas lines when OBSERVED PROBLEM OBSERVED REPAIR PARTS SERVICINGPARTS LIST Maxitrol ValveBLOWN UP VIEW OF BURNER ASSEMBLY PageITT Valve PARTS LISTBLOWN UP VIEW OF BURNER ASSEMBLY PagePage Page