New Buck Corporation MODEL FP-327-ZC manual INSTALLATION OF MODEL FP - 327- ZC

Page 13
INSTALLATION OF MODEL

INSTALLATION OF MODEL

FP - 327- ZC

WITH OPTIONAL WOODEN MANTEL

(1)When choosing the right location for your heater and mantel keep the following in mind:

NOTE: Due to high temperatures, this heater should be located out of traffic areas and away from furniture and draperies.

NOTE: Kit No. (PAKDM327) Optional Wooden Mantel for FP-327-ZC.

NOTE: See page 18 for “Gas Connection” and page 19 for “Gas Pressure Check”.

(2)Screen(s) can not be removed or altered (Position screen(s) in the closed position before leaving heater unattended).

(3)Follow instructions for assembly of (Optional) Wooden Mantel. See instructions supplied with mantel.

(4)After mantel has been assembled, slide the heater from the rear into the opening of the mantel.

NOTE: Place a cloth or blanket over the front portions of the mantel as not to scar the wood.

(5)Center the heater in the opening of the mantel. See Figure 6.

(6)Fasten mantel to hearth by using 1/2" wood screws.

(7)Insert the nine (9) wood screws provided with mantel through slots on nailing flange and secure in place. See Figure 6.

(8)Position mantel and fireplace into desired location.

NOTE: Hook gas supply line into heater. Check for leaks using soap and water, not an open flame.

NOTE: At this point, you may want to anchor the mantel to the wall or floor.

(9) Now you are ready to position the log set.

Page 11

Image 13
Contents NEW BUCK CORPORATION MODEL FP-327-ZCManufacturer NEW BUCK CORPORATION P.O. Box 8000 Highway 226 South Spruce Pine, NCPage TABLE OF CONTENTS Page SECTION I SAFETY INFORMATION WARNINGS Page Page CHOOSING THE LOCATION FOR YOUR FIREPLACE SECTION ZERO CLEARANCE INSTALLATIONGAS LINE DRAFTS3 1/4 Fireplace and Framing Dimensions inches7 1/2 PageFIREPLACE CLEARANCES INSTALLING THE FIREBOXInstall the Firebox Framing the FireboxCLEARANCES FINISHING YOUR FIREPLACEMUST BE FOLLOWED MANTEL PROFILES FOR ZERO CLEARANCE CABINETMANTEL 3/4 FLAT SURFACE MANTEL 3/4 FLAT SURFACEWITH OPTIONAL WOODEN MANTEL INSTALLATION OF MODEL FP - 327- ZCTOP MANTEL 1/2 WOOD SCREWSREAR OF HEATER MANTEL BASESECTION AFTER MARKET MOBILE HOME INSTALLATION DETERMINING FRESH-AIRFLOW FOR HEATER LOCATION PRODUCING ADEQUATE VENTILATIONVent-freeheater VENTILATION AIR FROM INSIDE BUILDING VENTILATION AIRVENTILATION AIR FROM OUTDOORS FLAME GAS CONNECTIONSEE DIAGRAM ON PAGE PLACEMENT OF LOGSGAS PRESSURE CHECK 3 1 2 Figure PLACEMENT OF LOGSPage LIGHTING INSTRUCTIONS MILLIVOLT VALVE ITT FOR YOUR SAFETY, READ BEFORE LIGHTINGWHAT TO DO IF YOU SMELL GAS BEFORE INSTALLING THERMOSTAT ROCKER SWITCHREMOVE METAL CONNECTOR PagePILOT BURNER IGNITOR ELECTRODETHERMO--COUPLEPILE PageTHERMOSTAT CONTROL OPERATION MANUAL LIGHTING PROCEDUREFOR YOUR SAFETY, READ BEFORE LIGHTING LIGHTING INSTRUCTIONS MODULATING VALVEMAXITROLto IGNITE and LIGHTING INSTRUCTIONSfor “LOW” for “HIGH”O.D.S PILOT BURNER IGNITER ELECTRODE THERMO-COUPLETO TURN OFF GAS TO APPLIANCE THERMOSTAT CONTROL OPERATION MANUAL LIGHTING PROCEDURENATURAL PILOT FLAME CHECKBURNER PROPANE PILOTWIRING DIAGRAM Rating 120 volts/60HZ/0.54 Amps NOTE #PESBRO84 Blower Model FP-327-ZCPage CLEANING IMPORTANT SAFEGUARDSTROUBLE SHOOTING Air in gas lines when OBSERVED PROBLEM OBSERVED SERVICING REPAIR PARTSMaxitrol Valve PARTS LISTPage BLOWN UP VIEW OF BURNER ASSEMBLYPARTS LIST ITT ValvePage BLOWN UP VIEW OF BURNER ASSEMBLYPage Page