New Buck Corporation MODEL FP-327-ZC Lighting Instructions, to IGNITE and, for “LOW”, for “HIGH”

Page 28
LIGHTING INSTRUCTIONS

LIGHTING INSTRUCTIONS

1.STOP! Read the safety information on the previous page.

2.Make sure manual shutoff valve is fully closed.

3.Open access panel door, located in lower front center of base for access to control knobs.

4.Turn off all electric power to the appliance.

5.Set thermostat (flame control) to lowest setting.

6. Push in and turn control knob clockwise

to the “OFF” position.

 

 

 

PILOT

 

 

 

 

 

 

 

 

 

2

 

1

 

 

 

 

 

 

 

 

 

FLAME

 

 

 

 

 

 

 

 

 

 

 

ON

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MERTIK MAXITROL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CONTROL

 

 

4

5

7 6

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FIGURE 3

IGNITE

OFF

to IGNITE and CONTROL KNOB

7.“Wait (5) five minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow step “B” in the safety information on the previous page. If you don’t smell gas, go to the next step.”

8.Find Pilot: follow the small metal tub from the right hand rear of the gas control valve.

 

The pilot is located behind the burner tube and in front of the rear log. Fully open the

 

manual shut-off valve.

to the “PILOT” position. Press in

9.

Turn control knob counterclockwise

 

control knob for (15) fifteen seconds (see figure 3).

to IGNITE and

10.

With control knob pressed in, turn control knob clockwise

then immediately back to PILOT with the button still pressed in. This will light the pilot. If needed, keep repeating this step until pilot lights.

11.Keep control knob pressed in for one (1) minute after lighting pilot. After (1) minute, release the control knob. If pilot goes out, repeat steps 1 through 9.

If the knob does not pop up when released, stop and immediately call your service techni- cian or gas supplier.

“If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call

 

your service technician or gas supplier.”

to “ON” position.

 

12.

Turn control knob counterclockwise

for “LOW”

13.

“Set thermostat (flame control) to desired setting. Turn clockwise

 

and counterclockwise

for “HIGH”.

 

 

Page 26

Image 28
Contents MODEL FP-327-ZC NEW BUCK CORPORATIONManufacturer NEW BUCK CORPORATION P.O. Box 8000 Highway 226 South Spruce Pine, NCPage TABLE OF CONTENTS Page SECTION I SAFETY INFORMATION WARNINGS Page Page SECTION ZERO CLEARANCE INSTALLATION CHOOSING THE LOCATION FOR YOUR FIREPLACEGAS LINE DRAFTSFireplace and Framing Dimensions inches 3 1/47 1/2 PageINSTALLING THE FIREBOX FIREPLACE CLEARANCESInstall the Firebox Framing the FireboxFINISHING YOUR FIREPLACE CLEARANCESMANTEL PROFILES FOR ZERO CLEARANCE CABINET MUST BE FOLLOWEDMANTEL 3/4 FLAT SURFACE MANTEL 3/4 FLAT SURFACEINSTALLATION OF MODEL FP - 327- ZC WITH OPTIONAL WOODEN MANTEL1/2 WOOD SCREWS TOP MANTELREAR OF HEATER MANTEL BASESECTION AFTER MARKET MOBILE HOME INSTALLATION PRODUCING ADEQUATE VENTILATION DETERMINING FRESH-AIRFLOW FOR HEATER LOCATIONVent-freeheater VENTILATION AIR VENTILATION AIR FROM INSIDE BUILDINGVENTILATION AIR FROM OUTDOORS GAS CONNECTION FLAMESEE DIAGRAM ON PAGE PLACEMENT OF LOGSGAS PRESSURE CHECK 3 1 2 Figure PLACEMENT OF LOGSPage LIGHTING INSTRUCTIONS MILLIVOLT VALVE ITT FOR YOUR SAFETY, READ BEFORE LIGHTINGWHAT TO DO IF YOU SMELL GAS ROCKER SWITCH BEFORE INSTALLING THERMOSTATREMOVE METAL CONNECTOR PageIGNITOR ELECTRODE PILOT BURNERTHERMO--COUPLEPILE PageMANUAL LIGHTING PROCEDURE THERMOSTAT CONTROL OPERATIONLIGHTING INSTRUCTIONS MODULATING VALVEMAXITROL FOR YOUR SAFETY, READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS to IGNITE andfor “LOW” for “HIGH”O.D.S PILOT BURNER IGNITER ELECTRODE THERMO-COUPLETO TURN OFF GAS TO APPLIANCE MANUAL LIGHTING PROCEDURE THERMOSTAT CONTROL OPERATIONFLAME CHECK NATURAL PILOTBURNER PROPANE PILOTWIRING DIAGRAM Rating 120 volts/60HZ/0.54 Amps NOTE #PESBRO84 Blower Model FP-327-ZCPage IMPORTANT SAFEGUARDS CLEANINGTROUBLE SHOOTING Air in gas lines when OBSERVED PROBLEM OBSERVED REPAIR PARTS SERVICINGPARTS LIST Maxitrol ValveBLOWN UP VIEW OF BURNER ASSEMBLY PageITT Valve PARTS LISTBLOWN UP VIEW OF BURNER ASSEMBLY PagePage Page