ADT Security Services 200 Plus manual Turning Off Burglary Protection

Page 55

5. Press the “Group description” button to turn on that specific group.

System Operation (cont’d)

6.Press Continue to display Action Menu 1.

7.Repeat steps 2 through 5 to turn on additional groups.

8.If an outside sounder is installed and optioned, wait to hear a short “ding” before leaving. The sounder's failure to annunciate the "ding" indicates ADT has not received the closing signal.

Turning On One or More Burglary Groups Using a Key or Card Reader

Before turning on, be sure to secure (or bypass) all protection points.

1.Press the Next button at or near the entry door and exit the premises. The red lamp above the button will start to flash.

Note: Failure of the light to flash indicates a door or window is open. Secure (or bypass) all protection and retry.

2.Within one minute, insert and swipe the access key or card. The red lamp on the exit button will illuminate steadily. If you are using a key, turn the key and lock the door.

Note: If the red lamp does not light, the system has not armed. If you are using a key, the cylinder will not turn and the door will not lock. Secure (or bypass) all protection and retry.

3.If an outside sounder is installed and optioned, wait to hear a short “ding” before leaving. The sounder's failure to annunciate the "ding" indicates ADT has not received the closing signal.

Turning Off Burglary Protection

If the operating panel is located within the protected area, enter through a pre-determined entry door. The operating panel will emit a steady tone indicating the entry delay.

Note: If you do not turn the system off prior to the expiration of the entry delay (steady tone stops), an alarm signal will be transmitted to the ADT Customer Monitoring Center.

– 55 –

Image 55

Contents Security System Table of Contents System Overview FOCUS 200 Plus FeaturesIntroduction Control Unit System Overview cont’dOperating Panel Protection Points and Groups User Access and SecuritySummary Automated Event Recording and PrintingFalse Alarm Prevention You must help eliminate false alarms False Alarm Prevention cont’dPreventing causes of false alarms False Alarm Prevention cont’d Operating Panel Functions Quick StartOffMore Enter ID Quick Start cont’dNormal Inactive Screen Front OfficeViewing Current Alarms Responding to AlarmsEntering Your Personal ID Number Hostage Navigational Menu SelectionsMore/First Selection Other Navigational Selections Quit/Previous SelectionAre on Code Accepted Continue Turn Off Turning BA Groups OffSummary Navigational Selections Some BA GroupsEnter choice Action Menus 1-4 Main FeaturesSee alarms Reset Quit More Assistance The ? Selection Action MenuExercise the ? Selection Exercise Turn on Burglary Protection See points Test Change close time Previous MoreExercise Test Bypass History Status Time Previous MoreExercise BYPASS/UNBYPASS Protection Points Bypass points See limits QuitExercise Name PNT/GPS SysInfo ID codes Name pnt/gps Load Previous FirstBack CHR Forward Left POS Right Quit ? First BA GroupSummary Operating Panel System Operation OverviewSystem Operation Overview cont’d Action Menus See alarms Reset Quit MoreSee points Test Change close time Previous More Bypass History StatusTime Previous More SysInfo ID codes Name pnt/gps Load Previous First User Data System ProgrammingEntering or Changing a User Name System Programming cont’dUser Name User Selection MenuUser Delete PrevChange Quit Next Deleting a User ID Code Assigning or Changing User Access Assigning Privilege Levels Assigning Burglary Group AccessSystem Programming cont’d Access Capability Assigning a User ID Code Assigning a Code and Card Cancel DateAssigning a User a Card/Key Code ? Time Changing the Time and DateTime Selection Menu Changing the Current TimeChanging the Current Date Setting Dates for Daylight Saving TimeDaily Operating Schedules Changing Daily Operating Schedules Hint The system will start display with today Mon-Sun Guidelines for Changing Daily Operating SchedulesGuidelines Changing Auto On/Off ScheduleSystem Programming cont’d ? Time Holiday Daylight Open/close Hstg Quit Current Changing Open/Close Schedule LimitsAdding or Changing Holiday Descriptions Holiday Description and DatesSystem Programming cont’d Changing Holiday Dates Group/Point DescriptionsSystem Programming cont’d Turning On Burglary Protection System OperationTurning On ALL Burglary Groups System Operation cont’d Lesson Turn on See alarms Reset Quit MoreTurning On One or More Burglary Groups Turning Off Burglary Protection Continue Turn Off Turn Off MenuTurning Off ALL Burglary Groups Are onResetting Current Alarms Triggering a Panic System History LogViewing the History Log On this screen On printer Quit History Selection MenuPrinting the History Log Description Alpha System Event History Log Alpha and Event CodesDescription Alpha Expansion Module Description Alpha Description Alpha Panic Description Alpha Other Access Bypassing/Unbypassing Burglary Protection Group Description PreviousNext Quit Bypass Selection MenuGroup Selection Menu Bypassing Protection PointsUnbypassing Protection Points Quit Bypass VVSBypassing/Unbypassing Vault Vibration Sensors VVS Extending Close Time Sending Messages to a Pager Burglary Protection Points Audible System TestProtection Points Visual System Test cont’dProtection Groups Testing Holdup, Fire, and Supervisory DevicesBell and Operating Panel Display Trouble or Error Display Description Action Troubleshooting GuideTime to turn on ‘Group Description’ or extend closing time Troubleshooting Guide cont’dFire, SPV or Holdup points bypassed Code Enforcement Fire Alarm Application NoteAbout Fire Alarm Codes ADT’s Focus 200 Plus Fire Alarm System CapabilitiesEmergency Evacuation Federal Communications Commission FCC Part 15 Statement Notification Federal Communications Commission FCC Part 68 Notice Canadian Department of Communications DOC Statement Limitations of this Alarm System Limitations of this Alarm System Index ADT Service personnel working on system76Limitations of this Alarm System ÊK3693-1SIA†Š