ADT Security Services 200 Plus manual ÊK3693-1SIA†Š

Page 88

LIMITED WARRANTY

Terms and Conditions Applying to Sale of Equipment

1.Limited Warranty.

Any part of the system, including the wiring, installed under this Agreement which proves to be defective in material or workmanship within 90 days of the date of completion of installation will be repaired or replaced at ADT's option with a new functionally operative part. Labor and material required to repair or replace such defective components or to make mechanical adjustments to the system will be free of charge for a period of 90 days following the completion of the original installation.

This warranty is extended only to the original consumer purchaser of the system and may be enforced only by such person.

To obtain service under this warranty, call or write our local ADT Service Department at the telephone number or address found in your local yellow pages.

Service pursuant to the warranty will be furnished only during ADT's normal working hours 8:00A.M. to 4:30P.M., Monday through Friday, except holidays. Services rendered outside the normal working hours of ADT are not within the scope of this warranty and any services requested to be performed at such times shall be charged for at ADT's then applicable rates for labor and material.

This warranty does not apply to the conditions listed below, and in the event customer calls ADT for service under the warranty and upon inspection it is found that one of these conditions has led to the inoperability or apparent inoperability of the system, a charge will be made for the service call of the ADT representative, whether or not he actually works on the system. Should it actually be necessary to make repairs to the system due to one of the "conditions Not Covered By Warranty", a charge will be made for such work at ADT's then applicable rates for labor and material.

Conditions Not Covered By Warranty.

A. Damage from accidents, acts of God, alterations, misuse, tampering or abuse. B. Failure of the customer to properly close or secure a door, window, or other point protected by a burglar alarm device. C. Failure of customer to properly follow operating instructions provided by ADT at time of installation or at a later date. D. Trouble in leased telephone. E. Trouble due to interruption of commercial power. F. Battery replacements.

This warranty is in lieu of all other express warranties. Any implied warranties of merchantability and fitness for a particular purpose are limited in duration to a period of 90 days from the date of completion of installation. The exclusive remedy of the customer hereunder shall be repair or replacement as stated above. Under no circumstances shall ADT be liable to the customer or any other person for incidental or consequential damages of any nature, including without limitation, damages for personal injury or damages to property, and, however occasioned, whether alleged as resulting from breach of warranty by ADT, the negligence of ADT, or otherwise, ADT's liability will in no event exceed the purchase price of the system. Some states may not allow limitations on how long an implied warranty lasts, or the exclusion or limitations of incidental or consequential damages, so the above limitations and exclusions may not apply to you, unless a longer period is required by applicable law. Any action against ADT in connection with a system must be commenced within one year after the cause of action has occurred.

No agent, employee or representative of ADT nor any other person is authorized to modify this warranty in any respect. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

2.Installation.

ADT agrees to install the equipment in a workmanlike manner in accordance with the following conditions: A. Customer will make premises available without interruption during ADT normal working hours 8:00A.M. to 4:30P.M., Monday through Friday, except Holidays. B. Customer understands that the installation will necessitate drilling into various parts of the premises: ADT intends, generally, to conceal wiring in the finished areas of the premises; however, there may be areas which, due to construction, decoration, or furnishing of the premises, ADT determines, in its sole discretion, that it would be impractical to conceal wiring and, in such cases, wiring will be exposed. C. Customer agrees to provide 110 VAC electrical outlets at designated locations for equipment requiring AC power. D. Customer to provide for lifting and replacing carpeting, if required, for installation of floor mats or wiring.

ALL RIGHTS RESERVED

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form, or by any means – electronic, mechanical, photocopying, recording, or otherwise without the written permission of ADT Security Systems, Inc. The material in this publication is for information purposes and subject to change without notice. ADT Security Systems, Inc. assumes no responsibility for any errors which may appear in this publication.

ADT Security Services, Inc.

One Town Center Road

Boca Raton, FL 33486

Copyright 2007

ÊK3693-1SIA†Š

K3693-1SIA 1/07 Rev A

Image 88
Contents Security System Table of Contents System Overview FOCUS 200 Plus FeaturesIntroduction Control Unit System Overview cont’dOperating Panel User Access and Security Protection Points and GroupsAutomated Event Recording and Printing SummaryFalse Alarm Prevention False Alarm Prevention cont’d You must help eliminate false alarmsPreventing causes of false alarms False Alarm Prevention cont’d Quick Start Operating Panel FunctionsQuick Start cont’d Normal Inactive ScreenFront Office OffMore Enter IDResponding to Alarms Viewing Current AlarmsEntering Your Personal ID Number Hostage Navigational Menu SelectionsMore/First Selection Quit/Previous Selection Other Navigational SelectionsTurning BA Groups Off Summary Navigational SelectionsSome BA Groups Are on Code Accepted Continue Turn OffAction Menus 1-4 Main Features See alarms Reset Quit More Assistance The ? SelectionAction Menu Enter choiceExercise the ? Selection See points Test Change close time Previous More Exercise Turn on Burglary ProtectionBypass History Status Time Previous More Exercise TestBypass points See limits Quit Exercise BYPASS/UNBYPASS Protection PointsSysInfo ID codes Name pnt/gps Load Previous First Exercise Name PNT/GPS? First BA Group Back CHR Forward Left POS Right QuitSummary System Operation Overview Operating PanelSystem Operation Overview cont’d See alarms Reset Quit More Action MenusSee points Test Change close time Previous More Bypass History StatusTime Previous More SysInfo ID codes Name pnt/gps Load Previous First System Programming User DataSystem Programming cont’d Entering or Changing a User NameUser Name User Selection MenuUser Delete PrevChange Quit Next Deleting a User ID Code Assigning or Changing User Access Assigning Burglary Group Access Assigning Privilege LevelsSystem Programming cont’d Access Capability Assigning a User ID Code Assigning a Code and Card Cancel DateAssigning a User a Card/Key Code Changing the Time and Date Time Selection MenuChanging the Current Time ? TimeSetting Dates for Daylight Saving Time Changing the Current DateDaily Operating Schedules Changing Daily Operating Schedules Guidelines for Changing Daily Operating Schedules Hint The system will start display with today Mon-SunChanging Auto On/Off Schedule GuidelinesSystem Programming cont’d Changing Open/Close Schedule Limits ? Time Holiday Daylight Open/close Hstg Quit CurrentHoliday Description and Dates Adding or Changing Holiday DescriptionsSystem Programming cont’d Group/Point Descriptions Changing Holiday DatesSystem Programming cont’d Turning On Burglary Protection System OperationTurning On ALL Burglary Groups System Operation cont’d Lesson Turn on See alarms Reset Quit MoreTurning On One or More Burglary Groups Turning Off Burglary Protection Turn Off Menu Turning Off ALL Burglary GroupsAre on Continue Turn OffResetting Current Alarms Triggering a Panic System History LogViewing the History Log On this screen On printer Quit History Selection MenuPrinting the History Log History Log Alpha and Event Codes Description Alpha System EventDescription Alpha Expansion Module Description Alpha Description Alpha Panic Description Alpha Other Access Bypassing/Unbypassing Burglary Protection Bypass Selection Menu Group Selection MenuBypassing Protection Points Group Description PreviousNext QuitUnbypassing Protection Points Quit Bypass VVSBypassing/Unbypassing Vault Vibration Sensors VVS Extending Close Time Sending Messages to a Pager System Test Burglary Protection Points AudibleSystem Test cont’d Protection Points VisualTesting Holdup, Fire, and Supervisory Devices Protection GroupsBell and Operating Panel Display Troubleshooting Guide Trouble or Error Display Description ActionTroubleshooting Guide cont’d Time to turn on ‘Group Description’ or extend closing timeFire, SPV or Holdup points bypassed Fire Alarm Application Note About Fire Alarm CodesADT’s Focus 200 Plus Fire Alarm System Capabilities Code EnforcementEmergency Evacuation Federal Communications Commission FCC Part 15 Statement Notification Federal Communications Commission FCC Part 68 Notice Canadian Department of Communications DOC Statement Limitations of this Alarm System Limitations of this Alarm System ADT Service personnel working on system76 IndexLimitations of this Alarm System ÊK3693-1SIA†Š