ADT Security Services 200 Plus manual Federal Communications Commission FCC Part 15 Statement

Page 80

FEDERAL COMMUNICATIONS COMMISSION (FCC) PART 15 STATEMENT

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

ADDITIONAL TELEPHONE COMPANY INFORMATION

The security control panel must be properly connected to the telephone line with USOC RJ-31X or RJ38X telephone jack and a matching 8-pin modular “Direct Connect Cord.” The FCC prohibits customer-provided terminal equipment to be connected to party line or to be used in conjunction with coin telephone service. Inter-connect rules may vary from state to state.

INCIDENCE OF HARM

In the unlikely event that the communicator should ever cause harm to the telephone network, the telephone company will notify the telephone subscriber that temporary discontinuance of service may be required; however, where prior notice is not practical, the telephone company may temporarily discontinue service. In the case of temporary discontinuance, the telephone company shall promptly notify the telephone subscriber, who will be given the opportunity to correct the situation. The customer also has the right to bring a complaint to the FCC if he feels the disconnection is unwarranted.

If your telephone equipment causes harm to the telephone network, the telephone company may discontinue your service temporarily. If possible, they will notify you in advance, but if advance notification is not practical, you will be notified as soon as possible. You will be notified of your right to file a complaint with the FCC.

CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES

The telephone company may make changes to its communications facilities, equipment, operations or procedures, where such action is reasonably required and proper in its business. Should any changes render the communicator incompatible with the telephone company facilities, the customer shall be given adequate notice to make modifications to maintain uninterrupted service.

80 –

Image 80
Contents Security System Table of Contents Introduction FOCUS 200 Plus FeaturesSystem Overview Operating Panel System Overview cont’dControl Unit User Access and Security Protection Points and GroupsAutomated Event Recording and Printing SummaryFalse Alarm Prevention False Alarm Prevention cont’d You must help eliminate false alarmsPreventing causes of false alarms False Alarm Prevention cont’d Quick Start Operating Panel FunctionsQuick Start cont’d Normal Inactive ScreenFront Office OffMore Enter IDResponding to Alarms Viewing Current AlarmsEntering Your Personal ID Number More/First Selection Navigational Menu SelectionsHostage Quit/Previous Selection Other Navigational SelectionsTurning BA Groups Off Summary Navigational SelectionsSome BA Groups Are on Code Accepted Continue Turn OffAction Menus 1-4 Main Features See alarms Reset Quit More Assistance The ? SelectionAction Menu Enter choiceExercise the ? Selection See points Test Change close time Previous More Exercise Turn on Burglary ProtectionBypass History Status Time Previous More Exercise TestBypass points See limits Quit Exercise BYPASS/UNBYPASS Protection PointsSysInfo ID codes Name pnt/gps Load Previous First Exercise Name PNT/GPS? First BA Group Back CHR Forward Left POS Right QuitSummary System Operation Overview Operating PanelSystem Operation Overview cont’d See alarms Reset Quit More Action MenusSee points Test Change close time Previous More Bypass History StatusTime Previous More SysInfo ID codes Name pnt/gps Load Previous First System Programming User DataSystem Programming cont’d Entering or Changing a User NameUser Delete PrevChange Quit Next User Selection MenuUser Name Deleting a User ID Code Assigning or Changing User Access Assigning Burglary Group Access Assigning Privilege LevelsSystem Programming cont’d Access Capability Assigning a User a Card/Key Code Assigning a Code and Card Cancel DateAssigning a User ID Code Changing the Time and Date Time Selection MenuChanging the Current Time ? TimeSetting Dates for Daylight Saving Time Changing the Current DateDaily Operating Schedules Changing Daily Operating Schedules Guidelines for Changing Daily Operating Schedules Hint The system will start display with today Mon-SunChanging Auto On/Off Schedule GuidelinesSystem Programming cont’d Changing Open/Close Schedule Limits ? Time Holiday Daylight Open/close Hstg Quit CurrentHoliday Description and Dates Adding or Changing Holiday DescriptionsSystem Programming cont’d Group/Point Descriptions Changing Holiday DatesSystem Programming cont’d Turning On ALL Burglary Groups System OperationTurning On Burglary Protection Turning On One or More Burglary Groups Lesson Turn on See alarms Reset Quit MoreSystem Operation cont’d Turning Off Burglary Protection Turn Off Menu Turning Off ALL Burglary GroupsAre on Continue Turn OffResetting Current Alarms Viewing the History Log System History LogTriggering a Panic Printing the History Log History Selection MenuOn this screen On printer Quit History Log Alpha and Event Codes Description Alpha System EventDescription Alpha Expansion Module Description Alpha Description Alpha Panic Description Alpha Other Access Bypassing/Unbypassing Burglary Protection Bypass Selection Menu Group Selection MenuBypassing Protection Points Group Description PreviousNext QuitBypassing/Unbypassing Vault Vibration Sensors VVS Quit Bypass VVSUnbypassing Protection Points Extending Close Time Sending Messages to a Pager System Test Burglary Protection Points AudibleSystem Test cont’d Protection Points VisualTesting Holdup, Fire, and Supervisory Devices Protection GroupsBell and Operating Panel Display Troubleshooting Guide Trouble or Error Display Description ActionTroubleshooting Guide cont’d Time to turn on ‘Group Description’ or extend closing timeFire, SPV or Holdup points bypassed Fire Alarm Application Note About Fire Alarm CodesADT’s Focus 200 Plus Fire Alarm System Capabilities Code EnforcementEmergency Evacuation Federal Communications Commission FCC Part 15 Statement Notification Federal Communications Commission FCC Part 68 Notice Canadian Department of Communications DOC Statement Limitations of this Alarm System Limitations of this Alarm System ADT Service personnel working on system76 IndexLimitations of this Alarm System ÊK3693-1SIA†Š