ADT Security Services 200 Plus manual Bell and Operating Panel Display

Page 74

System Test (cont’d)

7.Press Start test to begin the test.

8.Activate each Holdup, Fire, or Supervisory device. You will hear a beep once per minute as a reminder that the system is in the test mode. A history event will be logged for each sensor activated.

9.Upon completion of the test, return to the operating panel and re-enter your ID code to display Action Menu 1.

10.Press Reset to display the reset options.

11.Press Test to exit the test mode and to return the system to normal operation.

12.Press Continue to display Action Menu 1.

13.Check the system history to see that all points tested properly.

Bell and Operating Panel Display

Testing the bell and operating panel display will not affect any other operation, nor will it interfere with protection from any point or group.

1.Using the operating panel’s numeric keypad, enter a valid ID code to display Action Menu 1.

2.Press More to display Action Menu 2.

3.Press Test to display Test Menu 1.

4.Press More to display Test Menu 2.

5.Press Bell and display to begin automatic test of your system’s bell and display.

Note: A test pattern of all LCD elements will be shown for 4 seconds, and the bell will ring for the last 4 seconds of this 30-second test. Walk to an area where the bell can be heard to verify its operation.

6.The display will indicate the completion of the test.

7.Press Quit to display Test Menu 2.

8.Press Quit to display Action Menu 2.

– 74 –

Image 74

Contents Security System Table of Contents Introduction FOCUS 200 Plus FeaturesSystem Overview Operating Panel System Overview cont’dControl Unit User Access and Security Protection Points and GroupsAutomated Event Recording and Printing SummaryFalse Alarm Prevention False Alarm Prevention cont’d You must help eliminate false alarmsPreventing causes of false alarms False Alarm Prevention cont’d Quick Start Operating Panel FunctionsFront Office Quick Start cont’dNormal Inactive Screen OffMore Enter IDResponding to Alarms Viewing Current AlarmsEntering Your Personal ID Number More/First Selection Navigational Menu SelectionsHostage Quit/Previous Selection Other Navigational SelectionsSome BA Groups Turning BA Groups OffSummary Navigational Selections Are on Code Accepted Continue Turn OffAction Menu Action Menus 1-4 Main FeaturesSee alarms Reset Quit More Assistance The ? Selection Enter choiceExercise the ? Selection See points Test Change close time Previous More Exercise Turn on Burglary ProtectionBypass History Status Time Previous More Exercise TestBypass points See limits Quit Exercise BYPASS/UNBYPASS Protection PointsSysInfo ID codes Name pnt/gps Load Previous First Exercise Name PNT/GPS? First BA Group Back CHR Forward Left POS Right QuitSummary System Operation Overview Operating PanelSystem Operation Overview cont’d See alarms Reset Quit More Action MenusSee points Test Change close time Previous More Bypass History StatusTime Previous More SysInfo ID codes Name pnt/gps Load Previous First System Programming User DataSystem Programming cont’d Entering or Changing a User NameUser Delete PrevChange Quit Next User Selection MenuUser Name Deleting a User ID Code Assigning or Changing User Access Assigning Burglary Group Access Assigning Privilege LevelsSystem Programming cont’d Access Capability Assigning a User a Card/Key Code Assigning a Code and Card Cancel DateAssigning a User ID Code Changing the Current Time Changing the Time and DateTime Selection Menu ? TimeSetting Dates for Daylight Saving Time Changing the Current DateDaily Operating Schedules Changing Daily Operating Schedules Guidelines for Changing Daily Operating Schedules Hint The system will start display with today Mon-SunChanging Auto On/Off Schedule GuidelinesSystem Programming cont’d Changing Open/Close Schedule Limits ? Time Holiday Daylight Open/close Hstg Quit CurrentHoliday Description and Dates Adding or Changing Holiday DescriptionsSystem Programming cont’d Group/Point Descriptions Changing Holiday DatesSystem Programming cont’d Turning On ALL Burglary Groups System OperationTurning On Burglary Protection Turning On One or More Burglary Groups Lesson Turn on See alarms Reset Quit MoreSystem Operation cont’d Turning Off Burglary Protection Are on Turn Off MenuTurning Off ALL Burglary Groups Continue Turn OffResetting Current Alarms Viewing the History Log System History LogTriggering a Panic Printing the History Log History Selection MenuOn this screen On printer Quit History Log Alpha and Event Codes Description Alpha System EventDescription Alpha Expansion Module Description Alpha Description Alpha Panic Description Alpha Other Access Bypassing/Unbypassing Burglary Protection Bypassing Protection Points Bypass Selection MenuGroup Selection Menu Group Description PreviousNext QuitBypassing/Unbypassing Vault Vibration Sensors VVS Quit Bypass VVSUnbypassing Protection Points Extending Close Time Sending Messages to a Pager System Test Burglary Protection Points AudibleSystem Test cont’d Protection Points VisualTesting Holdup, Fire, and Supervisory Devices Protection GroupsBell and Operating Panel Display Troubleshooting Guide Trouble or Error Display Description ActionTroubleshooting Guide cont’d Time to turn on ‘Group Description’ or extend closing timeFire, SPV or Holdup points bypassed ADT’s Focus 200 Plus Fire Alarm System Capabilities Fire Alarm Application NoteAbout Fire Alarm Codes Code EnforcementEmergency Evacuation Federal Communications Commission FCC Part 15 Statement Notification Federal Communications Commission FCC Part 68 Notice Canadian Department of Communications DOC Statement Limitations of this Alarm System Limitations of this Alarm System ADT Service personnel working on system76 IndexLimitations of this Alarm System ÊK3693-1SIA†Š