Heat & Glo LifeStyle manual Diagram of the 6000TRI-IPI, 6000TRI-SP

Page 10

				28 1/2 [724mm]
	14 1/4
	[362mm]
					21 1/2 [548mm]
		8 [203mm]		11 5/8 [297mm]
		VENT COLLARS		11 5/8 [297mm]	ELECTRICAL
					ELECTRICAL	8 [203mm]
					ACCESS	8 [203mm]
						VENT
						COLLARS
	GAS LINE
	ACCESS
	38			25 1/4	34 5/8
	[965mm]			25 1/4	[879mm]
	[965mm]			[642mm]	[879mm]
				[642mm]
	2 1/8				3 1/2	26 7/8
	[55mm]				[90mm]	[682mm]
				36 1/8
				[916mm]
						12 3/4
	6 7/8 [174mm]	41 1/8				[323mm]
		[1044mm]
		TOP STANDOFFS		TOP VENT COLLARS
			REAR VENT COLLARS
			HOOD
			TRIM
			DOOR
		RATING PLATE
GAS		AND LABELS
GAS
LINE		GAS	ELECTRICAL
ACCESS		GAS	ELECTRICAL
ACCESS	CONTROLS			ACCESS
	CONTROLS			ACCESS
Figure 1. Diagram of the 6000TRI-IPI, 6000TRI-SP
10		Heat & Glo • 6000TRI-IPI, 6000TRI-SP • 385-901 Rev. F • 5/05

Image 10

Contents Installers Guide What to do if you smell gasSafety and Warning Information Table of Contents Log set assembly 6000TRI-IPI, 6000TRI-SPService Parts List / Liste des pièces de rechange 6000TRI-SP, 6000TRI-IPIIntermittent Pilot Ignition Valve Assembly 6000TRI-IPIStanding Pilot Ignition Valve Assembly 6000TRI-SPAppliance Certification Installation CodesHigh Altitude Installations CertificationIntroducing the Heat & Glo Gas Fireplaces Pre-install PreparationANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the 6000TRI-IPI, 6000TRI-SP Locating the Fireplace Constructing the Fireplace ChaseClearance Requirements Framing Dimensions Framing the FireplaceDVP90ST Tems or Components MAY be Used Installing the Vent SystemVent System Approvals Identifying Vent ComponentsVertical Venting Flue Restrictor InstructionsMAX .4 M Straight Up Vertical Venting Chart Venting with ONE 1 90 Elbow Venting with One 90 ElbowVenting with TWO 2 90 o Elbows Venting with Two 90 ElbowsVenting with Three 3 90 Elbows Venting with three 90 elbows+ V 1 FT + H 1 FT Installing Vent Components Install Support Brackets To Install the Heat ShieldContinue Adding Vent Components 12 Hole and Vent Pipe Vent Termination Attic FirestopVent Termination Minimum Clearances Proper Positioning Positioning, Leveling, Securing the FireplaceLeveling and Securing of a Fireplace Gas Control Systems Installing the Optional Heat-Zone KitVice Must be Wired Directly to the FIRE- Place Junction BOX Intermittent Pilot Ignition IPI SystemGas Pressure Requirements Gas Supply LinePressure Natural Gas Propane Intermittent Pilot Ignition IPI Wiring Diagram Wiring the Fireplace Finishing Sealant Material Hearth ExtensionsInstalling Trim, Logs, and Ember Material Air Shutter Setting Double-check for faulty componentsBefore Lighting the Fireplace Lighting the Fireplace After the InstallationFireplace Maintenance Important Turn OFF the GAS Before Servicing Your Fireplace